2010 Cadillac Truck SRX AWD V6-3.0L Page 1006

2010 Cadillac Truck SRX AWD V6-3.0L Page 1006

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Testing

1. Ignition ON, observe the DTC information with a scan tool. Verify that none of the following DTCs are set. DTC P0010, P0013, P0020,

P0023, P0335, P0336, P0340, P0341, P0345, P0346, P0365, P0366, P0390, or P0391.

瀚慖f any of the DTCs listed are set refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code

Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle) for further diagnosis.

2. Idle the engine at normal operating temperature. DTCs P0016, P0017, P0018, or P0019 should not set.

瀚慖f a DTC sets, inspect for the following and repair as necessary:

* The correct installation of the camshaft sensors

* The correct installation of the crankshaft sensor

* A timing chain tensioner condition

* An incorrectly installed timing chain

* Excessive play in the timing chain

* A mechanical cam actuator that is stuck in the full advance or retard position.

* A timing chain that jumped teeth

* A crankshaft reluctor wheel that has moved in relationship to top dead center (TDC) on the crankshaft

3. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Timing Chain Alignment Diagram (See: Engine, Cooling and Exhaust/Engine/Timing Components/Timing Component Alignment

Marks/Locations)

* Camshaft Timing Drive Components Cleaning and Inspection (See: Engine, Cooling and Exhaust/Engine/Service and Repair/Overhaul/81.

Camshaft Timing Drive Components Cleaning and Inspection)

* Crankshaft and Bearing Cleaning and Inspection (See: Engine, Cooling and Exhaust/Engine/Service and Repair/Overhaul/66. Crankshaft

and Bearing Cleaning and Inspection)

P16F3

DTC P0601-P0604, P0606, P0607, P0610, P062B, P062F, P0630, P16F3, or P2610 (ECM, LF1/LFW/LWR)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC P0601

- Control Module Read Only Memory Performance

DTC P0602

- Control Module Not Programmed