Thursday, September 10, 2020

2010 Cadillac CTS Sedan AWD V6-3.0L Page 2016

2010 Cadillac CTS Sedan AWD V6-3.0L Page 2016



* The TCM enables Torque management.



* The TCM inhibits TAP Up/Down function.



* The TCM turns OFF the high side driver.



Conditions for Clearing the DTC



* DTC P2728 is a Type C DTC.



* DTCs P2729 and P2730 are Type A DTCs.



Reference Information



Schematic Reference



Automatic Transmission Controls Schematics (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Diagrams)



Connector End View Reference



* Component Connector End Views (See: Diagrams/Connector Views)



* Inline Harness Connector End Views (See: Power and Ground Distribution/Multiple Junction Connector/Diagrams)



Description and Operation



* Transmission General Description (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Description and



Operation/Transmission General Description)



* Transmission Component and System Description (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Description and



Operation/Transmission Component and System Description)



* Electronic Component Description (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Description and



Operation/Electronic Component Description)



Electrical Information Reference



* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit Testing/Circuit Testing)



* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Connector Repairs/Connector Repairs)



* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit



Testing/Testing for Intermittent Conditions and Poor Connections)



* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Wiring Repairs/Wiring Repairs)



DTC Type Reference



Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code



(DTC) Type Definitions)



Scan Tool Reference



Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information



Special Tools



DT-47825-10 - Jumper Harness



Circuit/System Verification



1. Operate the vehicle in second gear long enough to ensure at least a 3掳C (5掳F) rise in TCM temperature.



2. Operate the vehicle in drive range. Allow the transmission to shift through all forward gear ranges. Verify with a scan tool the following test



status parameters display OK:



* Pressure Control Solenoid Valve 5 Performance Test Status



* Pressure Control Solenoid Valve 5 Control Circuit High Voltage Test Status



* Pressure Control Solenoid Valve 5 Control Circuit Low Voltage Test Status



3. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the



conditions that you observed from the Freeze Frame/Failure Records data.



Circuit/System Testing



Note: You must perform the Circuit/System Verification first.



1. Ignition OFF, remove the Q8 control solenoid valve assembly. Refer to Control Solenoid Valve and Transmission Control Module Assembly



Replacement (See: Powertrain Management/Transmission Control Systems/Actuators and Solenoids - Transmission and



Drivetrain/Actuators and Solenoids - A/T/Shift Solenoid/Service and Repair).



2. Perform the Control Solenoid Valve and Transmission Control Module Assembly Inspection (See: Transmission and Drivetrain/Automatic



Transmission/Transaxle/Testing and Inspection/Component Tests and General Diagnostics/Control Solenoid Valve and Transmission Control



Module Assembly Inspection).



3. Place the Q8 control solenoid valve assembly on a clean work surface near the transmission assembly.

No comments:

Post a Comment