Skip to main content

Mercedes Benz Truck G 55K AMG Mercedes2020-2010 Benz Truck G 55K AMG Technical Service Bulletin # LI58-40_P-048054 Date: 090929

Mercedes Benz Truck G 55K AMG Mercedes2020-2010 Benz Truck G 55K AMG Technical Service Bulletin # LI58-40_P-048054 Date: 090929



Computers/Controls - DAS/XD Software Update



DAS/XD ADD-ON 2009-08-26-1245 FOR PASSENGER CARS



Topic number LI58.40-P-048054



Version 1



Design group 58.40 Workshop equipment/MB testers



Date 09-29-2009



Validity DVD version 06/2009



Reason for change



Reason for block



Complaint:



ME 9.7



Model series: 463



Control unit programming for hardware object numbers 003 446 69 40 and 0034467140 reports: "The following control unit software versions are



available for control unit programming: 273 902 01 00 and 273 903 04 00" After control unit programming, the control unit cannot be started up.



ICM



2010 Mercedes Benz Truck G 55K AMG (463.271) V8-5.5L SC (113.993) 100



Model series: 204



Control unit programming for hardware object number 003 446 71 40 reports: "No newer control unit software found".



Cause:



For all complaints: XD and DAS diagnostic data.



Remedy:



DAS/XD add-on 2009-08-26-1245 for passenger cars.



This add-on can be installed over DAS/XD version 06/2009.



This add-on does not supersede any other add-ons and must be additionally installed.



Symptoms



Control unit/fault code



2010 Mercedes Benz Truck G 55K AMG (463.271) V8-5.5L SC (113.993) 101

Comments

Post a Comment

Popular posts from this blog

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.

P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.2010 Mercedes Benz E 63 AMG Sedan (212.077) V8­6.3L (156.985) Copyright ? 2013, ALLDATA 10.52SS Page 978 Possible cause: ­ A80 (Intelligent servo module for DIRECT SELECT) Affected functions: ­ Drive position selection ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ Test 1: Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' 1. Remedial action if control unit is faulty 'A80 (Intelligent servo module for DIRECT SELECT)' Operation number of operation texts and work units or standard texts and flat rates:27­0641Possible cause and remedy ­ Internal fault in control unit ­ Replace component A80 (Intelligent servo module for DIRECT SELECT). Additional measures ­ ­ Perform initial startup. Continue with button "F2" Initial startup The following procedure will guide you through all steps requ...
Read more

Dremel 4300-9/64 Versatile Corded Rotary Tool Kit with Flex Shaft and Hard Storage Case, High Power & Performance, Variable Speed- Engraver, Etcher, Sander, and Polisher, Ultimate Gift for the DIYER

  The Dremel 4300-9/64 is a versatile corded rotary tool kit designed for a wide range of applications, making it an excellent choice for DIY enthusiasts and professionals alike. Here’s an overview of its key features: ### Key Features 1. **Power and Performance**:    - **High Power Motor**: The 4300 features a powerful motor that provides efficient performance for various tasks, including engraving, etching, sanding, and polishing. 2. **Variable Speed**:    - **Adjustable RPM**: Offers a variable speed range (typically 5,000 to 35,000 RPM) for precise control, allowing you to match the speed to the material and task at hand. 3. **Flex Shaft Attachment**:    - **Enhanced Maneuverability**: The included flex shaft allows for more intricate work in tight spaces and provides a comfortable grip for detailed projects. 4. **Comprehensive Accessory Kit**:    - **Versatile Attachments**: Comes with a variety of attachments and accessories, including ...
Post a Comment
Read more

D138， Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts

D138 The message from the auxiliary oil pump is not available on the CAN bus. Possible cause: M42 (Electric transmission oil pump) / N89 (Transmission oil additional pump control unit) Affected functions: Engine start ------------------------------------------------- Test 1: Check component M42 (Electric transmission oil pump). Check component M42 (Electric transmission oil pump). Operation number of operation texts and work units or standard texts and flat rates:27-0641Test prerequisite Battery voltage is OK. Test sequence Switch off ignition. Disconnect connector at component N89 (Transmission oil additional pump control unit). Use multimeter to check voltage directly at jacks of wiring harness for component N89 (Transmission oil additional pump control unit). Switch on ignition. Measure direct voltage with multimeter between 1 and 4Specified value - Voltage [8,5...16,4] V Question Is the measurement value OK?...
Post a Comment
Read more