Monday, August 12, 2019

Jaguar S-Type (X200) V6-3.0L Technical Service Bulletin # 1-100 Date: 990401

Jaguar S-Type (X200) V6-3.0L Technical Service Bulletin # 1-100 Date: 990401



PDU - New Software



1-100



All



DATE



4/99



MODEL



All



NEW PDU SOFTWARE - JTP 627/4 AND JTP 628/3



ISSUE:



New PDU software has been released.



^ JTP 627/4 replaces 627/3.



^ JTP 628/3 replaces 628/2.



JTP 627/4 includes updates to previously released software issues and is an interim release of the S-TYPE software. Due to difficulties in obtaining



electrical data not all of the diagnostic software is available at this point. Additionally some of the software can only be provided as provisional due



to the number of inconsistencies anticipated. The following CD contents list details all of the software that is available on this CD.



JTP 628/3 has been modified to enable the PDU-PC software to handle the new alphanumeric VIN numbers used by the S-TYPE.



Note:



When entering a VIN for S-TYPE, you must enter the last 6 characters, not just the last 5 numbers. Without the letter, the PDU will interpret the



VIN as an XK8.



CD CONTENTS (VEHICLE APPLICATIONS ONLY)



Vehicle Data Viewer



XK8 All vehicles (1997 MY onwards)



XJ Series All vehicles (1995 MY onwards)



S-TYPE 2000 MY (PROVISIONAL DATA ONLY)



DTC Monitor



XK8 All vehicles (1997 MY onwards)



XJ Series All vehicles (1995 MY onwards)



S-TYPE 2000 MY (NO HELPTEXT AVAILABLE)



DATALOGGER



XK8 All vehicles (1997 MY onwards)



XJ Series All vehicles (1995 MY onwards)



S-TYPE 2000 MY



OBDII Report



XK8 All vehicles (1997 MY onwards)



XJ Series All vehicles (1995 MY onwards)



S-TYPE 2000 MY



Engine Set-Up



XK8 All vehicles (1997 MY onwards)



XJ Series All vehicles (1995 MY onwards)



S-TYPE NOT REQUIRED



CM Configuration



XK8 All vehicles (1997 MY onwards)



XJ Series All vehicles (1995 MY onwards)



S-TYPE NEW FEATURES (see section 3)



Vibration Analyzer



XK8 All vehicles (1997 MY onwards)



XJ Series All vehicles (1995 MY onwards)



S-TYPE 2000 MY



Guided Diagnostics



XK8 All vehicles (1997 MY onwards)



2000 Jaguar S-Type (X200) V6-3.0L Page 218



XJ Series All vehicles (1995 MY onwards)



S-TYPE Diagnose area only on the following systems:



Powertrain



ABS/Traction control/IVD



Adaptive damping



Air bag



Air conditioning



Network communications



Speed control



Driver Information Systems (Audio system, Navigation, Vehicle emergency System,Telephone)



Electric windows



Exterior lights



Gearshift interlock



Immobilization



Instrument pack



Power steering



Security/Locking



Reverse Parking Aid



The above systems are supported with manual checks to the area only. Full down to wire guided diagnostics are not available.



CM CONFIGURATION



The PDU contains configuration software for a significant number of control modules (CM) on the S-TYPE. The following tables provide data on



what level of configuration will be required under differing circumstances.



These CMs will require configuring using the PDU in the case a service replacement is installed.



2000 Jaguar S-Type (X200) V6-3.0L Page 219



These control modules will require configuration in the event being fitted as part of an accessory kit.



This control module will require configuring in the event of DTCs C1277 and C1278 (steering wheel angle) being cleared.



VID BLOCK PROGRAMMING



The Vehicle identification block (VID block) is a section of memory within the powertrain control module used to store data about all of the control



module configurations on the vehicle.This data is not used by the vehicle itself, and therefore failure to program the VID block will not affect the



vehicle's operation. The VID Block data is used by PDU during it's diagnostic and configuration routines to gather data about the vehicle.



PCM ID



The PCM Identifier is a unique code used to synchronize the PCM, Instrument pack and Steering column lock control module. If all three modules



are not synchronized then the vehicle will not start.



NEW WARNING MESSAGE



A new general warning message has been added to the start of all diagnostic routines. This message will appear whenever the PDU is switched on or



the diagnostic application is reloaded from the base station. Specific warning messages will still be provided within the diagnostic routines when



required.



DIAGNOSIS OF CONTINUOUS CRANKING PROBLEMS



The starter test routine for S-TYPE provides diagnostic procedures for continuous cranking problems. Unlike the majority of other applications this



routine assumes that the vehicle is not continuously cranking at the time the test starts. The test will operate correctly with either of the following two



conditions applied.



^ Starter relay removed



^ Battery supply strap to the starter motor removed



ACTION:



Ensure that this software is installed immediately. Retain the previous issues in a secure place as a backup CD-ROM in the event the new software is



damaged. Use JTP 627/4 for diagnosing 1995-97 MY Sedan Range, 1997-ON MY XK8, 1998-ON MY V8 XJ Series and 2000 MY S-TYPE.



Note:



When entering a VIN for S-TYPE, you must enter the last 6 characters, not just the last 5 numbers. Without the letter, the PDU will interpret the

No comments:

Post a Comment