2010 Cadillac CTS Sedan AWD V6-3.6L Page 878

2010 Cadillac CTS Sedan AWD V6-3.6L Page 878

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

1. Ignition ON, observe the DTC information with a scan tool. Verify no B52 HO2S heater DTCs are set.

瀚慖f a B52 HO2S heater DTC is set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code

Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle).

2. Engine running, observe the appropriate scan tool B52 HO2S voltage parameter. The reading should be within the range of 50-1,050 mV.

3. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Verify none of the following conditions exist:

* Lean or rich fuel injectors-Refer to Fuel Injector Solenoid Coil Test (w/LLT) (See: Powertrain Management/Computers and Control

Systems/Testing and Inspection/Component Tests and General Diagnostics/Fuel Injector Solenoid Coil Test)Fuel Injector Solenoid Coil

Test (w/LF1) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Injector/Testing and Inspection)

* Water intrusion in the B52 HO2S harness connector

* Low or high fuel system pressure-Refer to Fuel System Diagnosis (See: Powertrain Management/Computers and Control

Systems/Testing and Inspection/Component Tests and General Diagnostics/Fuel System Diagnosis)

* Fuel that is contaminated-Refer to Alcohol/Contaminants-in-Fuel Diagnosis (with Special Tool) (See: Powertrain

Management/Computers and Control Systems/Testing and Inspection/Component Tests and General

Diagnostics/Alcohol/Contaminants-in-Fuel Diagnosis (with Special Tool))Alcohol/Contaminants-in-Fuel Diagnosis (without Special

Tool) (See: Powertrain Management/Computers and Control Systems/Testing and Inspection/Component Tests and General

Diagnostics/Alcohol/Contaminants-in-Fuel Diagnosis (without Special Tool))

* Fuel saturation of the evaporative emission (EVAP) canister

* Exhaust leaks near the B52 HO2S

* Engine vacuum leaks

* Engine oil consumption-Refer to Oil Consumption Diagnosis (See: Engine, Cooling and Exhaust/Engine/Testing and

Inspection/Component Tests and General Diagnostics/Oil Consumption Diagnosis)

* Engine coolant consumption-Refer to Loss of Coolant (See: Engine, Cooling and Exhaust/Cooling System/Testing and

Inspection/Symptom Related Diagnostic Procedures/Loss of Coolant)

瀚慖f you find any of the above conditions, repair as necessary.

2. If all conditions test normal, test or replace the appropriate B52 HO2S.

Repair Instructions

Caution: Refer to Heated Oxygen Sensor Resistance Learn Reset Caution (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service Precautions/Heated Oxygen Sensor Resistance Learn Reset Caution).

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 (LF1) (See: Powertrain Management/Computers and Control Systems/Oxygen

Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 (LLT) (See: Powertrain Management/Computers and

Control Systems/Oxygen Sensor/Service and Repair)

* Heated Oxygen Sensor Replacement - Bank 1 Sensor 2 (LF1) (See: Powertrain Management/Computers and Control Systems/Oxygen

Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 1 Sensor 2 (LLT) (See: Powertrain Management/Computers and

Control Systems/Oxygen Sensor/Service and Repair)

* Heated Oxygen Sensor Replacement - Bank 2 Sensor 1 (LF1) (See: Powertrain Management/Computers and Control Systems/Oxygen

Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 2 Sensor 1 (LLT) (See: Powertrain Management/Computers and

Control Systems/Oxygen Sensor/Service and Repair)

* Heated Oxygen Sensor Replacement - Bank 2 Sensor 2 (LF1) (See: Powertrain Management/Computers and Control Systems/Oxygen

Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 2 Sensor 2 (LLT) (See: Powertrain Management/Computers and

Control Systems/Oxygen Sensor/Service and Repair)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming

P0016

DTC P0016, P0017, P0018, or P0019 (Without LF1)

Diagnostic Instructions