2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 332
Diagrams)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Object Detection Description and Operation (UFT) (See: Accessories and Optional Equipment/Collision Avoidance and Parking Assist
Systems/Description and Operation/Object Detection Description and Operation (UFT))Object Detection Description and Operation (UVC) (See:
Accessories and Optional Equipment/Collision Avoidance and Parking Assist Systems/Description and Operation/Object Detection Description and
Operation (UVC))Object Detection Description and Operation (UD7) (See: Accessories and Optional Equipment/Collision Avoidance and
Parking Assist Systems/Description and Operation/Object Detection Description and Operation (UD7))
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Verification
1. Verify that DTC B1405 is not set.
瀚慖f DTC is set, refer to DTC B1405 (See: B Code Charts/B1405).
2. Verify that DTC B0958 3A, DTC B0959 3A, DTC B0960 3A, or DTC B0961 3A is not set.
瀚慖f DTC is set, replace the appropriate object alarm sensor.
3. Transmission in REVERSE, verify the parking assist system is enabled and one audible beep sounds.
Circuit/System Testing
Single Object Alarm Sensor DTC Set
1. Ignition OFF, disconnect the harness connector at the appropriate object alarm sensor.
2. Ignition OFF for 30 seconds, test for less than 20 Ohms between the low reference circuit terminal 2 and ground.
瀚慖f greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the object
alarm module.
3. Ignition ON, transmission in REVERSE, test for 8.0-9.0 V between the voltage reference circuit terminal 1 and ground.
瀚慖f greater than the specified range, test the voltage reference circuit for a short to voltage. If the circuit tests normal, replace the object
alarm module.
瀚慖f less than the specified range, test the voltage reference circuit for a short to ground or an open/high resistance. If the circuit tests
normal, replace the object alarm module.
4. Ignition OFF, remove the malfunctioning object alarm sensor and swap locations with another properly functioning object alarm sensor.
Connect the harness connector at both sensors.
5. Ignition ON, verify the DTC is set for the new location in which the malfunctioning object alarm sensor is installed.
瀚慖f the DTC does not set for the new location, test the signal circuit terminal 3 for a short to voltage, short to ground, or an open/high
resistance. If the circuit tests normal, replace the object alarm module.
6. If the DTC sets for the new location in which the malfunctioning object alarm sensor is installed, replace the appropriate object alarm sensor.
Multiple Object Alarm Sensor DTCs Set
1. Ignition OFF, disconnect the harness connector at each of the object alarm sensors.
2. Ignition OFF for 30 seconds, test for less than 20 Ohms between the low reference circuit terminal 2 and ground.
瀚慖f greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the object
No comments:
Post a Comment