2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 341
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Verification
Ignition ON, observe the scan tool Park Assist Switch parameter while cycling the parking assist disable switch. The parameter should change
between Active and Inactive.
Circuit/System Testing
1. Ignition OFF, disconnect the harness connector at the I/P multifunction switch.
2. Test for less than 1.0 Ohms between the appropriate ground circuit listed below and ground:
* RPO X88/Z88 ground circuit terminal 3
* RPO Z75 ground circuit terminal 5
瀚慖f greater than the specified range, test the ground circuit for an open/high resistance.
3. Ignition ON, verify that the scan tool Park Assist Switch parameter is Inactive.
瀚慖f not the specified value, test the signal circuit terminal 2 for a short to ground. If the circuit tests normal, replace the object alarm
module.
4. Ignition OFF, connect a 3A fused jumper wire between signal circuit terminal 2 and ground.
5. Ignition ON, verify that the scan tool Park Assist Switch parameter is Active.
瀚慖f not the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the
object alarm module.
6. If all circuits test normal, test or replace the I/P multifunction switch.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Accessory Switch Replacement (Except Cadillac) (See: Instrument Panel, Gauges and Warning Indicators/Service and Repair/Accessory
Switch Replacement (Except Cadillac))Accessory Switch Replacement (Cadillac) (See: Instrument Panel, Gauges and Warning
Indicators/Service and Repair/Accessory Switch Replacement (Cadillac))
* Control Module References (See: Testing and Inspection/Programming and Relearning) for Object Alarm Module replacement, setup, and
programming.
B0968
DTC B0968
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptor
DTC B0968 00
- Parking Aid Switch Indicator Circuit
Mercedes Benz Diagnostic and Repair Information ,Wiring Diagrams. DTC. TSB. Types: TSB, DTC, Wiring Diagrams, OEM Procedures. Trusted by more than 400,000 technicians. OEM accurate fix for faster repairs. Repair Procedures and Labor Times. Factory Auto Repair info. Request A Demo Today. Factory-Correct Diagrams. Factory Part Numbers. Maintenance Schedules. Repair Procedures. Labor Times. Types: TSB, DTC.Mercedes,Mercedes,Benz,Mercedes-Benz UK,A,Class,B,Class,C,Class,E,Class,CLA,CLS,G,Class,GLA,A
Tuesday, November 19, 2019
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 341
Subscribe to:
Post Comments (Atom)
No comments:
Post a Comment