2010 Land Rover Range Rover (LM) V8-5.0L SC Technical Service Bulletin # Q090 Date: 091203
Campaign - Body Control Module Reconfiguration
No: Q090
Issue: 1
Date: 03 DEC 2009
THIS SERVICE ACTION IS VALID FOR A LIMITED TIME ONLY AND WILL EXPIRE 30 NOVEMBER 2011
SECTION: 418
SERVICE ACTION: Body Control Module Reconfiguration
AFFECTED VEHICLE RANGE:
Range Rover (LM) VIN: AA302697 - AA317013
Model Year: 2010
CONDITION SUMMARY:
Situation:
A limited number of 2010 model year Range Rover vehicles may experience a flat battery; this may lead to an engine no-start condition. If a door is
opened the vehicle electrical systems are powered for 15 minutes with an approximate 12 Amp current draw for this period. During certain scenarios
(such as loading / unloading the vehicle) the current drawn could deplete the battery to a level that cannot ensure an engine start. Example: if the
battery is at 60% capacity (State of Charge) and the vehicle loading / unloading period lasts one hour (opening and closing doors during this time),
then it is unlikely the engine will start.
Action:
Retailers are required to HOLD all affected vehicles in the above VIN range that are in their control and refrain from releasing the vehicles for new
or used vehicle sale pending completion of the rework action detailed in this Technical Bulletin. Vehicles must not be released until successful
reconfiguration of the Body Control Module (BCM). Affected vehicles in the hands of owners should be repaired at the next available opportunity.
2010 Land Rover Range Rover (LM) V8-5.0L SC Page 161
At the time of customer appointment, ensure that all outstanding service campaigns for each individual vehicle are identified and allocate sufficient
time and resources to complete all campaigns. For cars in Retailer inventory, this Service Action should be performed in conjunction with the
vehicle Pre-Delivery Inspection (PDI).
PARTS:
No parts necessary
TOOLS:
IDS with IDS-DVD119_V8.03 or later and Calibration File 20 or later
Midtronics PSC-550 Vehicle Power Supply
WARRANTY:
NOTE:
Always check DDW to verify that the vehicle is affected by this Service Action prior to undertaking any repairs. Repair procedures are under
constant review, and therefore times are subject to change; those quoted here must be taken as guidance only. Always refer to DDW to obtain the
latest repair time.
Warranty claims should be submitted quoting the Program Code 'Q090' together with the relevant Option Code. The Option Codes that contain drive
in / drive out can only be claimed if the vehicle is brought back into the workshop for this action alone to be undertaken.
This Service Action is valid for a limited time only and will expire 30 November 2011. All Warranty claims up to this date must be submitted for
payment within 30 days of completion of the repair.
REPAIR PROCEDURE
RECONFIGURE BODY CONTROL MODULE
CAUTION:
Ensure all ignition 'ON' / ignition 'OFF' requests are carried out; failure to perform these steps may cause damage to control modules in the vehicle.
CAUTION:
A Midtronics PSC-550 Vehicle Power Supply must be connected to the vehicle battery during IDS diagnosis / module programming.
1. Connect the Midtronics PSC-550 Vehicle Power Supply to the vehicle battery.
NOTE:
IDS must be loaded with IDS-DVD119_V8.03 or later and Calibration File 20 or later.
2. Connect the Integrated Diagnostic System (IDS) to the vehicle and begin a new Symptom Driven Diagnostic (SDD) session.
3. Follow the on-screen prompts, allowing SDD to read the VIN and identify the vehicle.
4. From the Session Type screen, select the 'Campaigns' session type.
5. Follow the on-screen prompts until the 'Recommendations' tab is visible.
6. From the list of Recommendations, select the following:
^ Configure existing module > Body control module
7. Follow all on-screen instructions to complete this task.
8. Exit the current SDD session.
2010 Land Rover Range Rover (LM) V8-5.0L SC Page 162
9. Disconnect IDS and the Midtronics PSC-550 Vehicle Power Supply from the vehicle.
No comments:
Post a Comment