Skip to main content

Mercedes Benz Truck GLK 350 Technical Problem # LI27-50_P-0497102 Date: 120703 A/T - Switches To Limp Home Mode And One Or More DTC's Stored Automatic transmission limp-home mode, fault codes 0717, 0718, 0722, 0723, 2200, 2201, 2204, 2205, 2206, 2207, 2767, 2768 Numero de tema: L127 5rnF-049710

Mercedes Benz Truck GLK 350 Technical Problem # LI27-50_P-0497102 Date: 120703
A/T - Switches To Limp Home Mode And One Or More DTC's Stored
Automatic transmission limp-home mode, fault codes 0717, 0718,
0722, 0723, 2200, 2201, 2204, 2205, 2206, 2207, 2767, 2768
Numero de tema: L127 5rnF-049710
Version: 2
Grupo de construccion: 27.50 Gear assembly
Edicion: 0703-2012
Validez: Automatic transmission 722.9 it is not possible to repair the EHS (VGS) in AMG vehicles
Motivo de modificacion: Note added: It is not possible to repair the EHS (VCS) in AMG vehicles
Reclamacion:
Automatic transmission 722.9 switches to limp-home while driving (gearshifts no longer possible) and/or one or more of the following fault codes
are stored or current:
For vehicles with VGS1
2200 2201 2204 2205 2206 2207
For vehicles with VGS2 or VGS3
 Mercedes Benz Truck GLK 350 36
0717, 0718, 0722, 0723, 2767, 2768
Causa:
Rpm sensor fault
Remedio:
Process the speed sensor fault codes completely using the DAS/Xentry guided test (possible as of DVD 01/2011 and add-on 1740). This may or may
not entail a replacement of the EHS.
In the case of hardware replacement (when SDS instructs to do so, see attachment) the adaptation data of the old transmission control unit is read out
in the DAS/Xentry guided test and transferred to the new control unit after the repair. Subsequently, the transmission control unit, which is bolted
onto the electrohydraulic controller unit (EHS), may only be replaced using the EHS repair kit (A000 270 17 00) In other cases SDS will provide
alternate instructions
See also the Akubis direct film: "Replacement of "fully integrated transmission control" (VGS) controller unit at electrohydraulic controller unit
(EHS) on automatic transmission 722.9"
The VGS Control Unit (Control Module) only is to be replaced for VGS2 and VGS3 Control Unit versions with these fault codes, when SDS
instructs to do so VGS Control Unit is available as EHS Repair Kit (A000 270 17 00) Complete valve body "Electrohydraulic Controller Unit
(EHS)" replacement is necessary for VCS1 Control Unit versions when SDS instructs to do so. Control Unit Version is identified from the
Transmission Control Unit Log.
Note in Cases where hardware replacement is specified:
This procedure differs from a complete valve body replacement as the adaptation data, coding and valve body calibration data are transferred from
the old VGS Control Unit to the new VGS control unit This data from the old VGS Control Unit is stored in the Star Diagnosis unit by processing
one of the above codes. The same Star Diagnosis SW stem unit MUST be used to process the fault code and perform initial startup of the new VGS
 Mercedes Benz Truck GLK 350 37
Control Unit. Failure to do so will result in the necessary data not being transferred and improper transmission functionality after VCS Control Unit
replacement.
1. Process the speed sensor fault code completely by following the instructions in DAS/Xentry related to the fault code Note: During the
replacement of the VGS Control Unit it is imperative that the position of the solenoid valves are noted and re-installed in their original positions
Failure to do so will cause a mismatch in the calibration data to respective solenoid valve(s) and subsequent shifting complaints.
2. Replace the VGS Control Unit per WIS instructions For the initial road test following VGS Control Unit replacement the vehicle must be driven
gently for the first several shifts in each gear since it will be necessary to bleed the air from the valve body. Until the air is bleed out irregular
shifting will be noticed momentarily and will clear up with subsequent shift processes. Because the adaptation data is transferred from the
original VGS Control Unit performing subsequent shift adaptations is not necessary.
Note:
It is not possible to repair the EHS (VGS) in AMG vehicles

Popular posts from this blog

2010 Mercedes Benz C 300 4MATIC (204.081) V6-3.0L (272.948) A L L Diagnostic Trouble Codes ( DTC ): P Code Charts P1240

2010 Mercedes Benz C 300 4MATIC (204.081) V6-3.0L (272.948)     A L L  Diagnostic Trouble Codes ( DTC ): P Code Charts P1240 The CAN bus is malfunctioning.   Test 1: Check the CAN communication with control unit Engine control module.   Test 2: Possible cause: - Drive train CAN bus Affected functions: - Engine diagnosis - Fuel system 1. Check the CAN communication with control unit Engine control module. Important note A CAN timeout fault code is set due to the absence of a CAN input signal.The cause of this may be not only the transmitter control unit, but also the CAN networking.Possible cause and remedy - Check CAN communication with affected control unit. - Check other control units for vehicle CAN bus failure in the stored faults. - CAN bus has loose contact or Open circuit. Continue with button F 2 Warning!Communication with ECU required. 2. No further information available.

2019 Mercedes-Benz X-Class

Launched for the brand new 3-Series coupe and convertible and provided on all engine variants, M Sport cars include a raft of extra equipment as standard compared to an SE model. Furthermore, passive safety is offered thanks to standard tools akin to seven airbags and the i-Size attachment system for 2 little one seats. Standard safety gear includes antilock disc brakes, stability and traction management, aspect airbags, side curtain airbags, knee airbags and Mercedes-Benz's "mbrace" emergency telematics system. The SLS is supposed to be Mercedes-Benz's ultimate vehicle, however it is also meant to be extra affordable and sensible to drive than the now-discontinued Mercedes SLR McLaren. Twelve (more than one-third) of the above differences are in the double digits. Although the price is affordable or not, are the primary disadvantages of space and rear seats for Mercedes-Benz C-Class 220 CDI vibration motor in the city. In case your body kit includes entrance and/or r...

Mercedes Benz C 300 4MATIC # LI80-57_P-051521 Date: 110601 30 Steering/Starting - No Crank/Start/ESL And ICM Don't Respond No Crank/No Start/ESL and ICM do not respond to key input

 Mercedes Benz C 300 4MATIC # LI80-57_P-051521 Date: 110601   30 Steering/Starting - No Crank/Start/ESL And ICM Don't Respond No Crank/No Start/ESL and ICM do not respond to key input Topic number LI80.57-P-051521 Version 1 Design group 80.57 Drive authorization systems (DAS) Date 06-01-2011 Validity All 204, 207 model vehicles Reason for change Complaint 1. No crank / no start / intermittent no crank 2. Communication via SDS to Electronic Ignition Switch N73 (EIS/EZS), and or short test may or may not be possible at time of fault 3. Below scenario: ^ When accessing the occupants compartment, the message center in the ICM will illuminate (note: eventually the message center will time out and shut down, and will not illuminate until the CAN is activated via the interior lock/unlock switch). ^ The key will turn in EIS N73. ^ The ESL N26/5 does not activate/respond (or the steering wheel remains unlocked at all times). ^ The warning icons in the ICM will not il...

2010 Mercedes Benz C 300 (204.054) V6-3.0L (272.947) Page 2499

2.1.3.2.1.4. Check power supply at control unit N15/3 (ETC [EGS] control unit). Test 2.1.3.2.1.4.1: Guided test 2.1.3.2.1.4.1. Guided test Operation number of operation texts and work units or standard texts and flat rates:27-0641Possible cause - Battery has incorrect charge state or is faulty. - Local undervoltage of component N15/3 (ETC [EGS] control unit) Test sequence - Erase fault memory. Continue with button "F2" Warning!Communication with ECU required. 2.1.3.2.1.5. Check power supply at control unit N15/5 (Electronic selector lever module control unit). Operation number of operation texts and work units or standard texts and flat rates:27-0641Test sequence - Switch off ignition. - Disconnect connector at component N15/5 (Electronic selector lever module control unit). - Switch on ignition. - [A.2] Measure direct voltage with multimeter between 2 and 1 [A.1] Status of relevant actual value: - Supply voltage (tml. 15):Warning! Communication with ECU required. Specified ...

2010 Cadillac Truck SRX AWD V6-3.0L Page 1240

2010 Cadillac Truck SRX AWD V6-3.0L Page 1240 Diagnosis (Without Special Tool) (See: Powertrain Management/Computers and Control Systems/Testing and Inspection/Component Tests and General Diagnostics/Alcohol/Contaminants-in-Fuel Diagnosis (Without Special Tool)). * Missing, restricted, or leaking exhaust components-Refer to Symptoms - Engine Exhaust (See: Engine, Cooling and Exhaust/Exhaust System/Testing and Inspection/Symptoms - Engine Exhaust). * Malfunctioning fuel injectors-Refer to Fuel Injector Solenoid Coil Test (LAU) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Injector/Testing and Inspection)Fuel Injector Solenoid Coil Test (LF1, LFW) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Injector/Testing and Inspection). * Vacuum hoses for splits, kinks, and improper connections * Insufficient fuel in the tank * Low fuel pressure-Refer to Fuel System Diagnosis (LF1 China) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Pump/Test...

Check the CAN communication with control unit N80 (Steering column module). Interior CAN bus

Part 1 One or more messages from control unit N80 (Steering column module) are not available on the CAN bus. Possible cause: Check the CAN communication with control unit N80 (Steering column module). Interior CAN bus Affected functions: CAN Communication Automatic transmission Function ------------------------------------------------- Test 1: Engine compartment CAN test Test 2: Check the CAN communication with control unit N80 (Steering column module). Test 3: Interior CAN check Engine compartment CAN test Test 1.1: Procedure in case of CAN faults Test 1.2: Evaluation of CAN fault codes Test 1.3: Further CAN test options Procedure in case of CAN faults Test 1.1.1: How do I quickly reach my goal? Test 1.1.2: General test information Test 1.1.3: General CAN fundamentals Test 1.1.4: Possible aids and their usage How do I quickly reach my goal? How do I quickly reach my goal?First call up menu item 'Evaluation of CAN...

Relay 'Circuit 87' ( Engine ) (P2505)

P2505 Relay 'Circuit 87' ( Engine ) (P2505) Possible cause: ­ N3/10 (ME­SFI [ME] control unit) ­ K40/4kK (Engine electronics and chassis relay) Affected functions: ­ Battery / On­board electrical system ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ Test 1: Check power supply of component N3/10 (ME­SFI [ME] control unit). Test 2: Arrangement of fuses Page 2562010 Mercedes Benz E 63 AMG Sedan (212.077) V8­6.3L (156.985) Copyright ? 2013, ALLDATA 10.52SS Page 257 1. Check power supply of component N3/10 (ME­SFI [ME] control unit). Test 1.1: Test voltage supply of circuit 87. 1.1. Test voltage supply of circuit 87. Figure legend ­ A ­ConnectionTest cable 35­pin socket box ­ 001 ­Sockets of component N3/10 (ME­SFI [ME] control unit) ­ 05 ­35­pin socket box ­ 050 ­126­pin socket box ­ 108 ­Test cable 266 589 01 63 00 ­ N3/10 (ME­SFI [ME] control unit) ­ II 1­63ConnectionTest cable ­ III 64­126ConnectionTest cable Warning! ­ ­ Connection A of test ca...

A/T - ECO Start/Stop Inoperative, DTC P0944 Stored In TCM ECO start/stop inoperative, fault code P0944 in transmission control unit

Mercedes-Benz Mercedes Benz OEM Parts Mercedes Benz OE Replacement Parts Technical Service Bulletin # LI27-57_P-0534962 Date: 120522 2010 Mercedes Benz SL 550 (230.471) V8-5.5L (273.965)   Page 29 A/T - ECO Start/Stop Inoperative, DTC P0944 Stored In TCM ECO start/stop inoperative, fault code P0944 in transmission control unit Topic number LI27.57-P-053496 Version 2 Design group 27.57 Oil pump Date 05-22-2012 Validity NAG2 FEPlus (722.9) with auxiliary oil pump with code B03 up to transmission sequence number 7.248.200 Reason for change Model series 251 deleted because model series 251 does not have ECO start/stop. Complaint: ECO start/stop inoperative, fault code P0944 in transmission control unit. Attachments Cause: Check valve in torque converter housing may be damaged. Leakage between torque converter housing and auxiliary oil pump. May affect transmissions with transmission sequence numbers starting with -07-xxx xxx. Remedy: Access v...

Mercedes Benz SLK 55 AMG No CAN message was received from control unit Engine management.

2010 Mercedes Benz SLK 55 AMG (171.473) V8-5.5L (113.989) Copyright ? 2013, ALLDATA 10.52SS Page 1 A L L Diagnostic Trouble Codes ( DTC ): Manufacturer Code Charts Part 1 No CAN message was received from control unit Engine management. Possible cause: - Fault in CAN communication with control unit Motor electronics. - Drive train CAN bus Affected functions: - CAN Communication - Automatic transmission Function ------------------------------------------------- Test 1: Engine compartment CAN test Test 2: Check the CAN communication with control unit Engine management. Test 3: Drive train CAN test 1. Engine compartment CAN test Test 1.1: Procedure in case of CAN faults Test 1.2: Evaluation of CAN fault codes Test 1.3: Further CAN test options 1.1. Procedure in case of CAN faults Test 1.1.1: How do I quickly reach my goal? Test 1.1.2: General test information Test 1.1.3: General CAN fundamentals Test 1.1.4: Possible aids and their usage 1.1.1. How do I quickly reach...