2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 610
wire thermistor and resistance through the sensor varies with temperature. The signal circuit is referenced from 5 V within the memory seat module
(MSM) and the temperature of the seat surface determines the signal circuit voltage. Once the seat reaches the set temperature, the module will then
cycle the control circuits of the heating elements ON and OFF in order to maintain the desired seat temperature based on the feedback voltage from
the sensors.
Conditions for Running the DTC
The heated seat system must be active.
Conditions for Setting the DTC
B2435 02 or B2440 02
The temperature sensor voltage drops below 0.8 volt for more than 1 second.
B2435 05 or B2440 05
The temperature sensor voltage is greater than 5 V for more than 1 second.
Action Taken When the DTC Sets
The heated seat function for the appropriate seat will be disabled.
Conditions for Clearing the DTC
* The current DTC will clear 3 seconds after the reference voltage returns to normal operating range, and the ignition is cycled OFF then back
to ACC or RUN.
* A history DTC will clear after 50 ignition cycles or with a scan tool using the clear DTCs function.
Reference Information
Schematic Reference
Heated/Cooled Seat Schematics ()
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Heated Seats Description and Operation (KA1) ()Heated Seats Description and Operation (KA6) ()
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Verification
Verify the type of vehicle and the heated seat system for which the DTC set.
If the DTC set in a vehicle equipped with memory, refer to Circuit/System Testing below.
If the DTC set in a hybrid or a non-hybrid vehicle without memory, refer to DTC B2435 or B2440 (HP2 or dealer installed w/o memory).
Circuit/System Testing
B2435 02 or B2435 05
1. Ignition OFF, disconnect the X2, X5 harness connectors at the MSM.
2. Test for 850 Ohms - 300 kOhms between the signal circuit terminal 4 X5 and the low reference circuit terminal 2 X2.
瀚慖f less than the specified range, test for a short between the signal and low reference circuits. If the circuits test normal, replace the seat
back heater element/temperature sensor.
瀚慖f greater than the specified range, test the signal and low reference circuits for a short to voltage or an open/high resistance. If the circuits
Mercedes Benz Diagnostic and Repair Information ,Wiring Diagrams. DTC. TSB. Types: TSB, DTC, Wiring Diagrams, OEM Procedures. Trusted by more than 400,000 technicians. OEM accurate fix for faster repairs. Repair Procedures and Labor Times. Factory Auto Repair info. Request A Demo Today. Factory-Correct Diagrams. Factory Part Numbers. Maintenance Schedules. Repair Procedures. Labor Times. Types: TSB, DTC.Mercedes,Mercedes,Benz,Mercedes-Benz UK,A,Class,B,Class,C,Class,E,Class,CLA,CLS,G,Class,GLA,A
Thursday, November 14, 2019
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 610
Subscribe to:
Post Comments (Atom)
No comments:
Post a Comment