Saturday, July 16, 2022

2010 Cadillac Truck SRX FWD V6-3.0L Page 851

2010 Cadillac Truck SRX FWD V6-3.0L Page 851



Electronic Suspension Control Description and Operation (See: Steering and Suspension/Suspension/Suspension Control ( Automatic - Electronic



)/Description and Operation)



Electrical Information Reference



* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit



Testing/Circuit Testing)



* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic



Procedures/Connector Repairs/Connector Repairs)



* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General



Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)



* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring



Repairs/Wiring Repairs)



Scan Tool Reference



Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information



Circuit/System Verification



Ignition ON, observe the scan tool Vertical Body Acceleration parameters. The parameters should be 0 m/s(2).



Circuit/System Testing



1. Ignition ON, verify that DTC C0870 is not present.



瀚慖f the DTC is present, refer to DTC C0870 (See: C Code Charts/C0870) to diagnose that DTC prior to this diagnostic.



2. Ignition OFF, disconnect the harness connector at the appropriate B162 vertical body acceleration sensor.



3. Ignition OFF, open/close doors, and wait 60 seconds. Test for less than 5 ohm between the low reference circuit terminal 3 and ground.



瀚慖f greater than the specified value, test the low reference circuit for short to voltage or an open/high resistance. If the circuit tests normal,



replace the K19 suspension control module.



4. Ignition ON, test for 4.8-5.2 V between the 5 V reference circuit terminal 1 and ground.



瀚慖f less than the specified range, test the 5 V reference circuit for a short to ground or an open/high resistance. If the circuit tests normal,



replace the K19 suspension control module.



瀚慖f greater than the specified range, test the 5 V reference circuit for a short to voltage. If the circuit tests normal, replace the K19



suspension control module.



5. Verify the scan tool Vertical Body Acceleration parameter is less than -3 m/s(2).



瀚慖f greater than the specified value, test the signal circuit for a short to ground. If the circuit tests normal, replace the K19 suspension



control module.



6. Install a fused jumper wire between the signal circuit terminal 2 and the low reference circuit terminal 3.



7. Verify the scan tool Vertical Body Acceleration parameter is greater than 3 m/s(2).



瀚慖f less than the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace



the K19 suspension control module.



8. If all circuits test normal, replace the B162 vertical body acceleration sensor.



Repair Instructions



Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.



* Electronic Suspension Front Vertical Accelerometer Replacement - Upper (See: Sensors and Switches/Sensors and Switches - Steering and



Suspension/Sensors and Switches - Suspension/Acceleration Sensor/Service and Repair/Electronic Suspension Front Vertical Accelerometer



Replacement - Upper)



* Electronic Suspension Rear Position Sensor Replacement (See: Sensors and Switches/Sensors and Switches - Steering and



Suspension/Sensors and Switches - Suspension/Ride Height Sensor/Service and Repair)



* Control Module References (See: Testing and Inspection/Programming and Relearning) for suspension control module replacement, setup



and programming



C0605



DTC C0595, C0600, or C0605

No comments:

Post a Comment