2010 Cadillac Truck SRX FWD V6-3.0L Page 1927

2010 Cadillac Truck SRX FWD V6-3.0L Page 1927

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

1. With the engine at normal operating temperature, raise the engine speed to 2,000 RPM for 10 s. DTCs P0010, P0013, P0020, P0023, P2088,

P2089, P2090, P2091, P2092, P2093, P2094, or P2095 should not set.

2. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Ignition OFF, disconnect the harness connector at the appropriate Q6 Camshaft Position Actuator Solenoid Valve.

2. Ignition ON, verify that a test lamp illuminates between the ignition circuit terminal 1 and ground.

瀚慖f the test lamp does not illuminate, test the circuit for a short to ground or an open/high resistance. If the circuit tests normal and the

ignition circuit fuse is open, test all the components connected to the ignition circuit and replace as necessary.

3. Connect a DMM, set on the diode setting, between the control circuit terminal 2 and ground. The voltage should be greater than 2 V.

瀚慖f the DMM displays OL, test the control circuit for a short to voltage or an open/high resistance. If the circuit/connections test normal,

replace the K20 Engine Control Module.

瀚慖f less than the specified value, test the control circuit for a short to ground. If the circuit tests normal, replace the K20 Engine Control

Module.

4. Command the Camshaft Position Actuator Solenoid Valve ON and OFF with a scan tool. The DMM should transition from greater than 2 V

when commanded OFF to less than 1 V, when commanded ON.

瀚慖f the circuit voltage does not correspond to the specified values, replace the K20 Engine Control Module.

5. If all circuits/connections test normal, test or replace the appropriate Q6 Camshaft Position Actuator Solenoid Valve.

Component Testing

1. Ignition OFF, disconnect the harness connector at the appropriate Q6 Camshaft Position Actuator Solenoid Valve.

2. Test for 7-12 ohm between the control terminal 2 and the ignition terminal 1 of the Q6 Camshaft Position Actuator Solenoid Valve.

瀚慖f not within the specified range, replace the Q6 Camshaft Position Actuator Solenoid Valve.

3. Test for infinite resistance between each terminal and the Q6 Camshaft Position Actuator Solenoid Valve housing.

瀚慖f not the specified value, replace the Q6 Camshaft Position Actuator Solenoid Valve.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Camshaft Position Actuator Solenoid Valve Solenoid Replacement - Bank 1 (Right Side) Intake (See: Engine, Cooling and

Exhaust/Engine/Actuators and Solenoids - Engine/Variable Valve Timing Solenoid/Service and Repair/Camshaft Position Actuator Solenoid

Valve Solenoid Replacement - Bank 1 (Right Side) Intake)

* Camshaft Position Actuator Solenoid Valve Solenoid Replacement - Bank 1 (Right Side) Exhaust (See: Engine, Cooling and

Exhaust/Engine/Actuators and Solenoids - Engine/Variable Valve Timing Solenoid/Service and Repair/Camshaft Position Actuator Solenoid

Valve Solenoid Replacement - Bank 1 (Right Side) Exhaust)

* Camshaft Position Actuator Solenoid Valve Solenoid Replacement - Bank 2 (Left Side) Intake (See: Engine, Cooling and

Exhaust/Engine/Actuators and Solenoids - Engine/Variable Valve Timing Solenoid/Service and Repair/Camshaft Position Actuator Solenoid

Valve Solenoid Replacement - Bank 2 (Left Side) Intake)

* Camshaft Position Actuator Solenoid Valve Solenoid Replacement - Bank 2 (Left Side) Exhaust (See: Engine, Cooling and

Exhaust/Engine/Actuators and Solenoids - Engine/Variable Valve Timing Solenoid/Service and Repair/Camshaft Position Actuator Solenoid

Valve Solenoid Replacement - Bank 2 (Left Side) Exhaust)