Thursday, November 11, 2021

2010 Cadillac Truck SRX FWD V6-3.0L Page 1739

2010 Cadillac Truck SRX FWD V6-3.0L Page 1739



* Perform the Service Fast Learn Adapts (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing and



Inspection/Programming and Relearning) following all transmission related repairs.



* Before replacing the TCM, perform the Control Solenoid Valve and Transmission Control Module Assembly Inspection (See:



Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing and Inspection/Component Tests and General



Diagnostics/6T70/6T75 - Automatic Transmission/Control Solenoid Valve and Transmission Control Module Assembly Inspection).



Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.



* Control Valve Lower Body and Upper Body Replacement (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Valve



Body/Service and Repair/6T70/6T75 - Automatic Transmission/Control Valve Lower Body and Upper Body Replacement)



* Low and Reverse Clutch and 1-2-3-4 Clutch Plate Removal (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Service



and Repair/Overhaul/8. Low and Reverse Clutch and 1-2-3-4 Clutch Plate Removal)



* Control Module References (See: Testing and Inspection/Programming and Relearning) for control solenoid valve assembly replacement,



setup, and programming



P0777



DTC P0776 or P0777



Diagnostic Instructions



* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System



Check - Vehicle) prior to using this diagnostic procedure.



* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an



overview of the diagnostic approach.



* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure



Instructions) provides an overview of each diagnostic category.



DTC Descriptors



DTC P0776



- Clutch Pressure Control (PC) Solenoid 2 - Stuck Off



DTC P0777



- Clutch Pressure Control (PC) Solenoid 2 - Stuck On



Circuit/System Description



The clutch pressure control (PC) solenoid 2 is part of the control solenoid valve assembly, which has no serviceable components. The PC solenoid



2 regulates transmission fluid pressure to the 3-5-Reverse clutch regulator valve which controls pressure to the 3-5-Reverse clutch. The



transmission control module (TCM) calculates gear ratio based on the RPM signals from the input speed sensor (ISS) and the output speed sensor



(OSS). The TCM compares the expected transmission gear ratio to the calculated gear ratio for each commanded gear.



Conditions for Running the DTC



P0776



* No ISS DTCs P0101, P0102, P0103, P0106, P0107, P0108, P0171, P0172, P0174, P0175, P0201, P0202, P0203, P0204, P0205, P0206,



P0207, P0208, P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307, P0308, P0401, P042E, P0716, P0717, P0722, P0723, or P182E.



* The ignition voltage is greater than 8.6 volts.



* The engine speed is greater than 400 RPM for 5 seconds.



* The transmission fluid temperature is 0掳C (32掳F) or greater.



* The transmission output speed is 16 RPM or greater, or the throttle position is 0.4 percent or greater.



* The throttle position signal is valid.



* The high side driver is commanded ON.



P0777



* No DTCs P0101, P0102, P0103, P0106, P0107, P0108, P0171, P0172, P0174, P0175, P0201, P0202, P0203, P0204, P0205, P0206, P0207,



P0208, P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307, P0308, P0401, P042E, P0716, P0717, P0722, P0723, or P182E.



* The transmission fluid temperature is 0掳C (32掳F) or greater.



* The transmission output shaft speed is 350 RPM or greater.



* The transmission input speed is 200 RPM or greater.



* The commanded gear is not 1st range.



* The high side driver is enabled.



Conditions for Setting the DTC

No comments:

Post a Comment