2010 Cadillac Truck SRX AWD V6-3.0L Page 2046

2010 Cadillac Truck SRX AWD V6-3.0L Page 2046

DTCs P2431, P2432 and P2433 are Type B DTCs.

Reference Information

Schematic Reference

Engine Controls Schematics (LAU) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics

(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)

Description and Operation

Secondary Air Injection System Description (See: Powertrain Management/Emission Control Systems/Air Injection/Description and Operation)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

1. Ignition ON, observe the diagnostic trouble code (DTC) information with a scan tool. Verify that DTCs P0641, P0642, P0643, P2227,

P2228, or P2229 are not set.

瀚慖f any of the above DTCs are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code

Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle) for further diagnosis.

2. Observe the scan tool Secondary Air Injection Pressure Sensor voltage parameter. The reading should be between 1.0-4.0 V.

3. Compare the scan tool BARO pressure parameter to the Altitude Versus Barometric Pressure (See: Powertrain Management/Computers and

Control Systems/Specifications/Altitude Versus Barometric Pressure) table. The BARO should be within the specified range displayed in the

table for the specific altitude.

瀚慖f not within the specified range, refer to DTC P2227, P2228, or P2229 (LAU) (See: P Code Charts/P2227) for further diagnosis.

4. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Ignition OFF, disconnect the harness connector at the B157 secondary air injection pressure sensor.

2. Ignition OFF and all vehicle systems OFF. It may take up to 2 minutes for all vehicle systems to power down. Test for less than 5 ohm

between the low reference circuit terminal 2 and ground.

瀚慖f greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the K20

ECM.

3. Ignition ON, test for 4.8-5.2 V between the 5 V reference circuit terminal 1 and ground.

瀚慖f less than the specified range, test the 5 V reference circuit for a short to ground or an open/high resistance. If the circuit tests normal,

replace the K20 ECM.

瀚慖f greater than the specified range, test the 5 V reference circuit for a short to voltage. If the circuit tests normal, replace the K20 ECM.

4. Verify the scan tool Secondary Air Injection Pressure Sensor voltage parameter is less than 0.5 V.

瀚慖f greater than the specified range, test the signal circuit terminal 3 for a short to voltage. If the circuit tests normal, replace the K20 ECM.