Saturday, June 19, 2021

2010 Cadillac Truck SRX FWD V6-3.0L Page 512

2010 Cadillac Truck SRX FWD V6-3.0L Page 512



Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)



Description and Operation



Heated/Vented Seat Description and Operation (See: Body and Frame/Seats/Seat Temperature Element/Description and Operation/Heated/Vented



Seat)



Electrical Information Reference



* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit



Testing/Circuit Testing)



* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic



Procedures/Connector Repairs/Connector Repairs)



* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General



Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)



* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring



Repairs/Wiring Repairs)



Scan Tool Reference



Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information



Circuit/System Testing



1. Ignition OFF, disconnect the harness connector at the appropriate E14F or E14H rear seat cushion heating element.



2. Test for less than 10 Ohms between the low reference circuit terminal D and ground.



瀚慖f greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit test normal, replace the K29R



rear seat heating control module.



3. Ignition ON, test for 4.8 - 5.2 V between the signal circuit terminal C and ground.



瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace



the K29R rear seat heating control module.



瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the K29R rear seat



heating control module.



4. If all circuits test normal, test or replace the E14 rear seat cushion heating element.



Component Testing



E14F or E14H Seat Cushion Heating Element



1. Ignition OFF, disconnect the harness connector at the appropriate E14F or E14H rear seat cushion heating element.



2. Test for 500 Ohms - 300 kOhms between the signal circuit terminal C and the low reference circuit terminal D.



瀚慖f not within the specified range, replace the E14 rear seat cushion heating element.



Repair Instructions



Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.



* Rear Seat Cushion Heater Replacement (40 Percent Seat) (See: Body and Frame/Seats/Seat Temperature Element/Service and Repair/Rear



Seat Cushion Heater Replacement (40 Percent Seat))Rear Seat Cushion Heater Replacement (60 Percent Seat) (See: Body and



Frame/Seats/Seat Temperature Element/Service and Repair/Rear Seat Cushion Heater Replacement (60 Percent Seat))



* Control Module References (See: Testing and Inspection/Programming and Relearning) for rear seat heating control module replacement,



setup, and programming



With Memory A45



DTC B1925 or B2170 (With Memory A45)



Diagnostic Instructions



* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System



Check - Vehicle) prior to using this diagnostic procedure.



* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an



overview of the diagnostic approach.



* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure



Instructions) provides an overview of each diagnostic category.

No comments:

Post a Comment