2010 Cadillac CTS Sedan AWD V6-3.6L Page 472

2010 Cadillac CTS Sedan AWD V6-3.6L Page 472

* Terminal 3 (LHD)

* Terminal 1 (RHD)

瀚慖f less than the specified range, test the 5 V reference circuit for a short to ground or an open/high resistance. If the circuit tests normal,

replace the MSM.

瀚慖f greater than the specified range, test the 5 V reference circuit for a short to voltage. If the circuit tests normal, replace the MSM.

4. Verify the scan tool Driver Seat Recline Sensor parameter is less than 1.0 V.

瀚慖f greater than the specified range, test the signal circuit terminal 2 for a short to voltage. If the circuit tests normal, replace the MSM.

5. Install a 3 A fused jumper wire between the signal circuit terminal 2 and the appropriate 5 V reference circuit terminal listed below. Verify

the scan tool Driver Seat Recline Sensor parameter is greater than 4.75 V.

* Terminal 3 (LHD)

* Terminal 1 (RHD)

瀚慖f less than the specified range, test the signal circuit for short to ground or an open/high resistance. If the circuit tests normal, replace the

MSM.

6. If all circuits test normal, test or replace the seat recline position sensor.

B2355 01, B2355 06, B2365 01, B2365 06, B2375 01 or B2375 06

1. Ignition OFF, disconnect the X2 harness connector at the appropriate seat adjuster motor.

2. Test for less than 2 Ohms between the appropriate low reference circuit listed below and ground.

* Seat horizontal motor sensor terminal C

* Seat front vertical motor sensor terminal C LHD)

* Seat front vertical motor sensor terminal A RHD)

* Seat rear vertical motor sensor terminal A (LHD)

* Seat rear vertical motor sensor terminal C (RHD)

瀚慖f greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the MSM.

3. Ignition ON, test for 4.8 - 5.2 V between the appropriate 5 V reference circuit terminal listed below and ground.

* Seat horizontal motor sensor terminal A

* Seat front vertical motor sensor terminal A (LHD)

* Seat front vertical motor sensor terminal C (RHD)

* Seat rear vertical motor sensor terminal C (LHD)

* Seat rear vertical motor sensor terminal A (RHD)

瀚慖f less than the specified range, test the 5 V reference circuit for a short to ground or an open/high resistance. If the circuit tests normal,

replace the MSM.

瀚慖f greater than the specified range, test the 5 V reference circuit for a short to voltage. If the circuit tests normal, replace the MSM.

4. Verify the appropriate scan tool driver seat sensor parameter is less than 1.0 V.

瀚慖f greater than the specified range, test the signal circuit terminal B for a short to voltage. If the circuit tests normal, replace the MSM.

5. Install a 3 A fused jumper wire between the appropriate signal circuit terminal and 5 V reference circuit terminal listed below. Verify the

appropriate scan tool driver seat position sensor parameter is greater than 4.75 V.

* Seat horizontal position sensor terminal B and terminal A

* Seat front vertical position sensor terminal B and terminal A (LHD)

* Seat front vertical position sensor terminal B and terminal C (RHD)

* Seat rear vertical position sensor terminal B and terminal C (LHD)

* Seat rear vertical position sensor terminal B and terminal A (RHD)

瀚慖f less than the specified range, test the signal circuit for short to ground or an open/high resistance. If the circuit tests normal, replace the

MSM.

6. If all circuits test normal, test or replace the appropriate seat position sensor.

B1850 01 or B1850 06

1. Ignition OFF, disconnect the harness connector at the lumbar motor.

2. Test for less than 2 Ohms between the appropriate low reference circuit terminal listed below and ground: