2010 Cadillac Truck SRX AWD V6-3.0L Page 2124

2010 Cadillac Truck SRX AWD V6-3.0L Page 2124

Automatic Transmission Controls Schematics (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Diagrams/Electrical

Diagrams)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

Description and Operation

Transmission Component and System Description (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Description and

Operation/AF40-6 - Automatic Transmission/Transmission Component and System Description)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning)

Circuit/System Verification

1. Ensure the transmission fluid temperature is between 50-80掳C (122-176掳F).

2. Operate the vehicle in 2nd gear long enough to ensure at least a 3掳C (5掳F) rise in transmission fluid temperature, then operate the vehicle in

Park for 5 s.

3. Observe the scan tool Brake Band Pressure Control Solenoid Valve Current parameter. The reading should be between 0.1-1.1 A.

Circuit/System Testing

Command the Shift Brake Pressure Control Solenoid Valve with a scan tool. The value should change from 0.0-1.0 A.

If the value does not change, turn ignition OFF, remove the K71 Transmission Control Module. Connect a test lamp between the low reference

circuit terminal 16 X2 at the K71 Transmission Control Module and the voltage supply component circuit terminal 21 X2 at the K71 Transmission

Control Module. Command the Shift Brake Pressure Control Solenoid Valve with a scan tool. The test lamp has to illuminate brighter with

increasing current.

If the test lamp always illuminates or always does not illuminate, replace the K71 Transmission Control Module.

Component Testing

Static Test

1. Ignition OFF, remove the K71 Transmission Control Module.

2. Test for 5-5.6 ohm at 20掳C (68掳F) between the low reference circuit terminal 16 X2 and the voltage supply circuit terminal 21 X2.

瀚慖f less than the specified range, test the wiring harness for internal short. If the circuit test normal, replace the Q27E Pressure Control

Solenoid Valve 5.

3. Test for infinite resistance between each terminal and the low reference circuit terminal 16 X2 and also to the voltage supply circuit terminal

21 X2.

瀚慖f less than the specified range, replace the wiring harness.

4. If all circuit test normal, perform the Control Solenoid Valve Inspection (M36 and MXE) (See: Transmission and Drivetrain/Automatic

Transmission/Transaxle/Testing and Inspection/Component Tests and General Diagnostics/AF40-6 - Automatic Transmission).

瀚慖f the inspection tests normal, replace the control valve body.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Control valve body replacement-Refer to Control Valve Body Replacement (See: Transmission and Drivetrain/Automatic