2010 Cadillac Truck SRX AWD V6-3.0L Page 1933

2010 Cadillac Truck SRX AWD V6-3.0L Page 1933

Module.

4. Command the Camshaft Position Actuator Solenoid Valve ON and OFF with a scan tool. The DMM should transition from greater than 2 V

when commanded OFF to less than 1 V, when commanded ON.

瀚慖f the circuit voltage does not correspond to the specified values, replace the K20 Engine Control Module.

5. If all circuits/connections test normal, test or replace the appropriate Q6 Camshaft Position Actuator Solenoid Valve.

Component Testing

1. Ignition OFF, disconnect the harness connector at the appropriate Q6 Camshaft Position Actuator Solenoid Valve.

2. Test for 7-12 ohm between the control terminal 2 and the ignition terminal 1 of the Q6 Camshaft Position Actuator Solenoid Valve.

瀚慖f not within the specified range, replace the Q6 Camshaft Position Actuator Solenoid Valve.

3. Test for infinite resistance between each terminal and the Q6 Camshaft Position Actuator Solenoid Valve housing.

瀚慖f not the specified value, replace the Q6 Camshaft Position Actuator Solenoid Valve.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Camshaft Position Actuator Solenoid Valve Solenoid Replacement - Bank 1 (Right Side) Intake (See: Engine, Cooling and

Exhaust/Engine/Actuators and Solenoids - Engine/Variable Valve Timing Solenoid/Service and Repair/Camshaft Position Actuator Solenoid

Valve Solenoid Replacement - Bank 1 (Right Side) Intake)

* Camshaft Position Actuator Solenoid Valve Solenoid Replacement - Bank 1 (Right Side) Exhaust (See: Engine, Cooling and

Exhaust/Engine/Actuators and Solenoids - Engine/Variable Valve Timing Solenoid/Service and Repair/Camshaft Position Actuator Solenoid

Valve Solenoid Replacement - Bank 1 (Right Side) Exhaust)

* Camshaft Position Actuator Solenoid Valve Solenoid Replacement - Bank 2 (Left Side) Intake (See: Engine, Cooling and

Exhaust/Engine/Actuators and Solenoids - Engine/Variable Valve Timing Solenoid/Service and Repair/Camshaft Position Actuator Solenoid

Valve Solenoid Replacement - Bank 2 (Left Side) Intake)

* Camshaft Position Actuator Solenoid Valve Solenoid Replacement - Bank 2 (Left Side) Exhaust (See: Engine, Cooling and

Exhaust/Engine/Actuators and Solenoids - Engine/Variable Valve Timing Solenoid/Service and Repair/Camshaft Position Actuator Solenoid

Valve Solenoid Replacement - Bank 2 (Left Side) Exhaust)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for Engine Control Module replacement, setup, and

programming

P2095

DTC P0010, P0013, P0020, P0023, P2088, P2089, P2090, P2091, P2092, P2093, P2094, or P2095 (Without LF1, LFW)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC P0010

- Intake Camshaft Position Actuator Solenoid Valve Control Circuit Bank 1

DTC P0013

- Exhaust Camshaft Position Actuator Solenoid Valve Control Circuit Bank 1

DTC P0020

- Intake Camshaft Position Actuator Solenoid Valve Control Circuit Bank 2

DTC P0023

- Exhaust Camshaft Position Actuator Solenoid Valve Control Circuit Bank 2

DTC P2088

- Intake Camshaft Position Actuator Solenoid Valve Control Circuit Low Voltage Bank 1