2010 Cadillac Truck SRX AWD V6-3.0L Page 1770

2010 Cadillac Truck SRX AWD V6-3.0L Page 1770

Description and Operation

* Transmission General Description (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Description and

Operation/6T70/6T75 - Automatic Transmission/Transmission General Description)

* Electronic Component Description (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Description and

Operation/6T70/6T75 - Automatic Transmission/Electronic Component Description) for control solenoid valve assembly

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Special Tools

DT-47825-20 - Jumper Harness

Circuit/System Verification

1. If there are any other transmission related DTCs set, diagnose those DTCs first. Refer to Diagnostic Trouble Code (DTC) List - Vehicle (

See: Diagnostic Trouble Code Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle).

2. Engine idling in Park with parking brake applied, and drive wheels chocked.

3. Monitor the TFP Switch 1, TFP Switch 3, TFP Switch 4, and TFP Switch 5 parameters with a scan tool.

4. Place the gear select lever in Park, Reverse, and Neutral range. Verify the TFP Switch 1, TFP Switch 3, TFP Switch 4, and TFP Switch 5

parameter states are correct for each range. Refer to Transmission Fluid Pressure Switch Logic (See: Specifications/Mechanical

Specifications/Automatic Transmission/Transaxle/System Specifications/6T70/6T75 - Automatic Transmission/Transmission Fluid Pressure

Switch Logic).

5. Place the gear select lever in Drive range. Command the shift transmission with a scan tool through all forward ranges. Verify the TFP

Switch 1, TFP Switch 3, TFP Switch 4, and TFP Switch 5 parameter states are correct for each range. Refer to Transmission Fluid Pressure

Switch Logic (See: Specifications/Mechanical Specifications/Automatic Transmission/Transaxle/System Specifications/6T70/6T75 -

Automatic Transmission/Transmission Fluid Pressure Switch Logic).

6. Operate the vehicle within the conditions for running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

Note: You must perform the Circuit/System Verification first.

1. Ignition OFF. Remove the control solenoid valve assembly. Refer to Control Solenoid Valve and Transmission Control Module Assembly

Replacement (See: Powertrain Management/Transmission Control Systems/Actuators and Solenoids - Transmission and

Drivetrain/Actuators and Solenoids - A/T/Shift Solenoid/Service and Repair).

2. Perform the Control Solenoid Valve and Transmission Control Module Assembly Inspection (See: Transmission and Drivetrain/Automatic

Transmission/Transaxle/Testing and Inspection/Component Tests and General Diagnostics/6T70/6T75 - Automatic Transmission/Control

Solenoid Valve and Transmission Control Module Assembly Inspection).

3. Place the control solenoid valve assembly on a clean work surface near the transmission assembly.

4. Connect DT-47825-20 - jumper harness between the vehicle wire harness electrical connector, and the control solenoid valve assembly

electrical connector.

5. Ignition ON, verify with a scan tool that the TFP Switch 1, TFP Switch 3, TFP Switch 4, and TFP Switch 5 parameters changes states when

gently pushing on each TFP switch with the eraser end of a pencil.

瀚慖f any TFP Switch parameter does not change states, replace the control solenoid valve assembly.

Repair Instructions

Note:

* Perform the Service Fast Learn Adapts (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing and

Inspection/Programming and Relearning) following all transmission related repairs.