2010 Cadillac Truck SRX AWD V6-3.0L Page 1786

2010 Cadillac Truck SRX AWD V6-3.0L Page 1786

1. Ignition OFF. Remove the control solenoid valve assembly. Refer to Control Solenoid Valve and Transmission Control Module Assembly

Replacement (See: Powertrain Management/Transmission Control Systems/Actuators and Solenoids - Transmission and

Drivetrain/Actuators and Solenoids - A/T/Shift Solenoid/Service and Repair).

2. Perform the Control Solenoid Valve and Transmission Control Module Assembly Inspection (See: Transmission and Drivetrain/Automatic

Transmission/Transaxle/Testing and Inspection/Component Tests and General Diagnostics/6T70/6T75 - Automatic Transmission/Control

Solenoid Valve and Transmission Control Module Assembly Inspection).

3. Place the control solenoid valve assembly on a clean work surface near the transmission assembly.

4. Connect DT-47825-20 - jumper harness between the vehicle wire harness electrical connector, and the control solenoid valve assembly

electrical connector.

5. Ignition ON, verify with a scan tool that the TFP Switch 1, TFP Switch 3, TFP Switch 4, and TFP Switch 5 parameters changes states when

gently pushing on each TFP switch with the eraser end of a pencil.

瀚慖f any TFP Switch parameter does not change states, replace the control solenoid valve assembly.

Repair Instructions

Note:

* Perform the Service Fast Learn Adapts (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing and

Inspection/Programming and Relearning) following all transmission related repairs.

* Before replacing the TCM, perform the Control Solenoid Valve and Transmission Control Module Assembly Inspection (See: Transmission

and Drivetrain/Automatic Transmission/Transaxle/Testing and Inspection/Component Tests and General Diagnostics/6T70/6T75 - Automatic

Transmission/Control Solenoid Valve and Transmission Control Module Assembly Inspection).

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

Control Module References (See: Testing and Inspection/Programming and Relearning) for control solenoid valve assembly replacement, setup, or

programming

P0877

DTC P0877 or P0878

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC P0877

- Transmission Fluid Pressure (TFP) Switch 4 Circuit Low Voltage

DTC P0878

- Transmission Fluid Pressure (TFP) Switch 4 Circuit High Voltage

Diagnostic Fault Information

Circuit/System Description

The transmission fluid pressure (TFP) switch 4 is part of the control solenoid valve assembly which has no serviceable parts. The TCM supplies a

signal circuit to the TFP switch 4. The TFP switch 4 has an internal case ground. TFP switch 4 is normally closed or LOW. When oil pressure is

present at the TFP switch 4, the switch is open or HIGH. The normally LOW pressure control solenoid 5 controls pressure to the 1-2-3-4 clutch

regulator valve. The TCM monitors the TFP switch 4 to determine the position of the 1-2-3-4 clutch regulator valve. When the 1-2-3-4 clutch is

commanded OFF, pressure is present on the TFP switch 4. When the 1-2-3-4 clutch is commanded ON, the 1-2-3-4 clutch regulator valve moves

and pressure to the TFP switch 4 is exhausted through the 1-2-3-4 clutch regulator valve.

Conditions for Running the DTC