Monday, March 29, 2021

2010 Cadillac CTS Sedan AWD V6-3.6L Page 872

2010 Cadillac CTS Sedan AWD V6-3.6L Page 872



* Oil seepage at the CMP actuator solenoid connector



瀚慖f a condition is found, replace Camshaft Position Actuator Solenoid Valve.



7. Ignition OFF, swap the Camshaft Position Actuator Solenoid Valve with a Camshaft Position Actuator Solenoid Valve that is operating



correctly.



Note: This step is testing the mechanical CMP actuator for the camshaft that set the DTC.



8. Engine idling. Command the appropriate Camshaft Position Actuator from 0 degrees to 40 degrees and back to zero while observing the



appropriate scan tool Camshaft Position Variance parameters. The Camshaft Position Variance should be less than 2 degrees in each of the



commanded states.



瀚慖f greater than the specified value, replace the mechanical camshaft position actuator.



9. If all circuits/connections test normal, test or replace the Camshaft Position Actuator Solenoid Valve.



Component Testing



1. Ignition OFF, disconnect the harness connector at the appropriate Camshaft Position Actuator Solenoid Valve.



2. Test for 7-12 ohm between the control terminal 2 and the ignition terminal 1 of the solenoid.



瀚慖f not within the specified range, replace the Camshaft Position Actuator Solenoid Valve.



3. Test for infinite resistance between each terminal and the solenoid housing.



瀚慖f not the specified value, replace the Camshaft Position Actuator Solenoid Valve.



Repair Instructions



Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.



* Camshaft Position Actuator Solenoid Valve Solenoid Replacement - Bank 1 (Right Side) Intake (See: Engine, Cooling and



Exhaust/Engine/Actuators and Solenoids - Engine/Variable Valve Timing Solenoid/Service and Repair/Camshaft Position Actuator Solenoid



Valve Solenoid Replacement - Bank 1 (Right Side) Intake)



* Camshaft Position Actuator Solenoid Valve Solenoid Replacement - Bank 1 (Right Side) Exhaust (See: Engine, Cooling and



Exhaust/Engine/Actuators and Solenoids - Engine/Variable Valve Timing Solenoid/Service and Repair/Camshaft Position Actuator Solenoid



Valve Solenoid Replacement - Bank 1 (Right Side) Exhaust)



* Camshaft Position Actuator Solenoid Valve Solenoid Replacement - Bank 2 (Left Side) Intake (See: Engine, Cooling and



Exhaust/Engine/Actuators and Solenoids - Engine/Variable Valve Timing Solenoid/Service and Repair/Camshaft Position Actuator Solenoid



Valve Solenoid Replacement - Bank 2 (Left Side) Intake)



* Camshaft Position Actuator Solenoid Valve Solenoid Replacement - Bank 2 (Left Side) Exhaust (See: Engine, Cooling and



Exhaust/Engine/Actuators and Solenoids - Engine/Variable Valve Timing Solenoid/Service and Repair/Camshaft Position Actuator Solenoid



Valve Solenoid Replacement - Bank 2 (Left Side) Exhaust)



* Camshaft Position Actuator Replacement - Bank 1 (Right Side) Intake (See: Engine, Cooling and Exhaust/Engine/Camshaft, Lifters and



Push Rods/Camshaft/Service and Repair/Camshaft Position Actuator Replacement - Bank 1 (Right Side) Intake)



* Camshaft Position Actuator Replacement - Bank 1 (Right Side) Exhaust (See: Engine, Cooling and Exhaust/Engine/Camshaft, Lifters and



Push Rods/Camshaft/Service and Repair/Camshaft Position Actuator Replacement - Bank 1 (Right Side) Exhaust)



* Camshaft Position Actuator Replacement - Bank 2 (Left Side) Intake (See: Engine, Cooling and Exhaust/Engine/Camshaft, Lifters and Push



Rods/Camshaft/Service and Repair/Camshaft Position Actuator Replacement - Bank 2 (Left Side) Intake)



* Camshaft Position Actuator Replacement - Bank 2 (Left Side) Exhaust (See: Engine, Cooling and Exhaust/Engine/Camshaft, Lifters and



Push Rods/Camshaft/Service and Repair/Camshaft Position Actuator Replacement - Bank 2 (Left Side) Exhaust)



* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming



P014A



DTC P013A, P013C, P013E, or P014A (LLT)



Diagnostic Instructions



* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System



Check - Vehicle) prior to using this diagnostic procedure.



* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an



overview of the diagnostic approach.



* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure



Instructions) provides an overview of each diagnostic category.

No comments:

Post a Comment