2010 Cadillac CTS Sedan AWD V6-3.6L Page 893

2010 Cadillac CTS Sedan AWD V6-3.6L Page 893

DTC P0019

- Crankshaft Position (CKP) - Exhaust Camshaft Position (CMP) Correlation Bank 2

Circuit/System Description

The engine control module (ECM) uses the crankshaft position (CKP) sensor and the camshaft position (CMP) sensor pulses to monitor the

correlation between the crankshaft and the camshaft position. An improper relative position can be caused by either engine timing or improper

indexing of the camshaft drive chain.

Conditions for Running the DTC

* Before the ECM can report DTC P0016, P0017, P0018, or P0019 failed, DTCs P0010, P0011, P0013, P0014, P0020, P0021, P0023, P0024,

P0335, P0336, P0338, P0341, P0342, P0343, P0346, P0347, P0348, P0366, P0367, P0368, P0391, P0392, P0393, P2088, P2089, P2090,

P2091, P2092, P2093, P2094, and P2095 must run and pass.

* The engine is operating for greater than 50 seconds.

* The engine coolant temperature is between 0-95掳C (32-203掳F).

* The calculated engine oil temperature is less than 120掳C (248掳F).

* DTC P0016, P0017, P0018, and P0019 run continuously once the above conditions are met for approximately 10 minutes.

Conditions for Setting the DTC

The ECM detects a deviation in the relationship between a camshaft and the crankshaft. The ECM detects the learned camshaft angle is greater than

10 degrees advanced or 10 degrees retarded in relationship to the crankshaft.

OR

The ECM detects the actual camshaft angle is advanced 15 degrees or retarded 21 degrees in relationship to the camshaft parked/reference position.

Action Taken When the DTC Sets

DTCs P0016, P0017, P0018, and P0019 are type B DTCs.

Conditions for Clearing the DTC

DTCs P0016, P0017, P0018, and P0019 are type B DTCs.

Diagnostic Aids

* Inspect the engine for any recent engine mechanical repairs. An incorrectly installed camshaft, camshaft actuator, camshaft sensor, crankshaft

sensor, or timing chain can cause this DTC to set.

* The presence of DTCs P0008 and P0009 along with P0016, P0017, P0018, and P0019 indicates a possible condition with the primary timing

chain and the alignment between both intermediate sprockets and the crankshaft. Or, the crankshaft reluctor wheel has moved and is no

longer referenced to top dead center (TDC).

* Observe the Desired Intake Camshaft Position and the Camshaft Position parameters with a scan tool before a DTC sets. This may help to

isolate whether a condition is specific to one camshaft, one bank, or caused by a condition with the primary crankshaft timing.

Reference Information

Schematic Reference

Engine Controls Schematics (LLT) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics

(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Description and Operation

Camshaft Actuator System Description (See: Powertrain Management/Computers and Control Systems/Description and Operation/Camshaft

Actuator System Description)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/Circuit

Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Wiring Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code