2010 Cadillac CTS Sedan AWD V6-3.6L Page 118

2010 Cadillac CTS Sedan AWD V6-3.6L Page 118

* Driver roof rail module terminal A and SDM terminal 17 X2

* Passenger roof rail module terminal A and SDM terminal 53 X2

* Left side impact module terminal 2 and SDM terminal 13 X2

* Right side impact module terminal 2 and SDM terminal 16 X2

* Driver seat belt pretensioner terminal 1 and SDM terminal 9 X2

* Passenger seat belt pretensioner terminal 1 and SDM terminal 12 X2

瀚慖f greater than the specified range, test the control circuit for an open/high resistance.

11. Test for less than 1 ohm between the following low control circuit terminals.

* I/P module Stage 1 terminal 2 X1 and SDM terminal 6

* I/P module Stage 2 terminal 1 X2 and SDM terminal 7

* Driver roof rail module terminal B and SDM terminal 18 X2

* Passenger roof rail module terminal B and SDM terminal 54 X2

* Left side impact module terminal 1 and SDM terminal 14 X2

* Right side impact module terminal 1 and SDM terminal 15 X2

* Driver seat belt pretensioner terminal 2 and SDM terminal 10 X2

* Passenger seat belt pretensioner terminal 2 and SDM terminal 11 X2

瀚慖f greater than the specified range, test the control circuit for an open/high resistance.

12. If all circuits test normal, replace the SDM.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Instrument Panel Inflatable Restraint Module Replacement (See: Restraints and Safety Systems/Air Bag Systems/Air Bag/Service and

Repair/Removal and Replacement/Instrument Panel Inflatable Restraint Module Replacement)

* Roof Side Rail Inflatable Restraint Module Replacement (See: Restraints and Safety Systems/Air Bag Systems/Air Bag/Service and

Repair/Removal and Replacement/Roof Side Rail Inflatable Restraint Module Replacement)

* Seat Belt Retractor Pretensioner Replacement - Front (W2E) (See: Restraints and Safety Systems/Seat Belt Systems/Seat Belt

Tensioner/Service and Repair/Removal and Replacement/Seat Belt Retractor Pretensioner Replacement - Front (W2E))Seat Belt Retractor

Pretensioner Replacement - Front (AQ9) (See: Restraints and Safety Systems/Seat Belt Systems/Seat Belt Tensioner/Service and

Repair/Removal and Replacement/Seat Belt Retractor Pretensioner Replacement - Front (AQ9))

* SIR/SRS Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/Wiring Repairs/SIR/SRS Wiring Repairs)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for SDM replacement, setup, and programming

B0023

DTC B0014-B0045

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC B0014 01

- Driver Side Deployment Loop Short to Battery - Seat Air Bag

DTC B0014 02

- Driver Side Deployment Loop Short to Ground - Seat Air Bag

DTC B0014 04

- Driver Side Deployment Loop Open Circuit - Seat Air Bag

DTC B0014 0D

- Driver Side Deployment Loop Resistance Above Threshold - Seat Air Bag

DTC B0014 0E

- Driver Side Deployment Loop Resistance Below Threshold - Seat Air Bag