2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2244
voltage signal. The BCM sends a serial data message to the engine control module (ECM)/powertrain control module (PCM) indicating the status
of the stop lamps.
Conditions for Running the DTC
The engine is ON.
Conditions for Setting the DTC
* The ECM/PCM receives an invalid brake pedal status serial data message from the BCM.
* This diagnostic runs continuously.
Actions Taken When the DTC Sets
* The cruise control system becomes disabled.
* The malfunction indicator lamp (MIL) will not illuminate.
Conditions for Clearing the DTC
* The condition responsible for setting the DTC no longer exists.
* A history DTC will clear after 40 malfunction-free ignition cycles have occurred.
Reference Information
Schematic Reference
* Cruise Control Schematics (See: Cruise Control/Diagrams/Electrical Diagrams)
* Exterior Lights Schematics (See: Diagrams/Electrical Diagrams/Lighting and Horns/System Diagram/Exterior Lights Schematics)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Cruise Control Description and Operation (See: Cruise Control/Description and Operation)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Verification
1. Verify that DTC P0572 or P0573 is not set.
瀚慖f DTC is set, refer to Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic
Overview/Diagnostic System Check - Vehicle).
2. Verify that DTC P0703 is not set.
瀚慖f DTC is set, replace the BCM. Clear the DTC and road test the vehicle. If DTC resets, replace the ECM/PCM.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
Control Module References (See: Testing and Inspection/Programming and Relearning) for BCM, ECM or PCM replacement, setup, and
programming
2ML70 - Automatic Transmission
Mercedes Benz Diagnostic and Repair Information ,Wiring Diagrams. DTC. TSB. Types: TSB, DTC, Wiring Diagrams, OEM Procedures. Trusted by more than 400,000 technicians. OEM accurate fix for faster repairs. Repair Procedures and Labor Times. Factory Auto Repair info. Request A Demo Today. Factory-Correct Diagrams. Factory Part Numbers. Maintenance Schedules. Repair Procedures. Labor Times. Types: TSB, DTC.Mercedes,Mercedes,Benz,Mercedes-Benz UK,A,Class,B,Class,C,Class,E,Class,CLA,CLS,G,Class,GLA,A
Subscribe to:
Post Comments (Atom)
-
P179D The redundancy system for DIRECT SELECT was activated. There is a signal above the permissible limit value.2010 Mercedes Benz E 63 A...
-
The Dremel 4300-9/64 is a versatile corded rotary tool kit designed for a wide range of applications, making it an excellent choice for DI...
-
BMW (Benz-Wesbach) is a well-known and respected luxury brand in the European automotive market, particularly for sports cars like the M5. ...
No comments:
Post a Comment