Monday, November 2, 2020

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1815

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1815

3. Ignition ON, verify the appropriate scan tool B52 HO2S parameter is approximately 450 mV.

瀚慖f less than the specified value, test the signal circuit for a short to ground. If the circuit tests normal, replace the K20 ECM.

瀚慖f greater than the specified value, test the signal circuit for a short to voltage. If the circuit tests normal, replace the K20 ECM.

4. Ignition ON, install a 3 A fused jumper wire between the signal circuit terminal B and ground. Verify the appropriate scan tool B52 HO2S

parameter is less than 60 mV.

瀚慖f greater than the specified range, test the signal circuit for an open/high resistance. If the circuit tests normal, replace the K20 ECM.

5. If all circuits test normal, replace the appropriate B52 HO2S.

Repair Instructions

Caution: Refer to Heated Oxygen Sensor Resistance Learn Reset Caution (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service Precautions/Heated Oxygen Sensor Resistance Learn Reset Caution).

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 (1500 Series) (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 (2500 Series) (See: Powertrain

Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)

* Heated Oxygen Sensor Replacement - Bank 1 Sensor 2 (1500 Series) (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 1 Sensor 2 (2500 Series) (See: Powertrain

Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)

* Heated Oxygen Sensor Replacement - Bank 2 Sensor 1 (1500 Series) (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 2 Sensor 1 (2500 Series) (See: Powertrain

Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)

* Heated Oxygen Sensor Replacement - Bank 2 Sensor 2 (1500 Series) (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 2 Sensor 2 (2500 Series) (See: Powertrain

Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)

* Control Module References (See: Testing and Inspection/Programming and Relearning)for ECM replacement, setup, and programming

P0152

DTC P0131, P0132, P0137, P0138, P0151, P0152, P0157, or P0158

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC P0131

- HO2S Circuit Low Voltage Bank 1 Sensor 1

DTC P0132

- HO2S Circuit High Voltage Bank 1 Sensor 1

DTC P0137

- HO2S Circuit Low Voltage Bank 1 Sensor 2

DTC P0138

- HO2S Circuit High Voltage Bank 1 Sensor 2

DTC P0151

- HO2S Circuit Low Voltage Bank 2 Sensor 1

DTC P0152

- HO2S Circuit High Voltage Bank 2 Sensor 1

DTC P0157

- HO2S Circuit Low Voltage Bank 2 Sensor 2

No comments:

Post a Comment