2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 472
Outside Rearview Mirror Schematics (See: Body and Frame/Mirrors/Diagrams/Electrical Diagrams/Outside Rearview Mirror Schematics)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Outside Mirror Description and Operation (Heated Mirrors) (See: Body and Frame/Mirrors/Description and Operation/Outside Mirror Description
and Operation (Heated Mirrors))Outside Mirror Description and Operation (Power Mirrors) (See: Body and Frame/Mirrors/Description and
Operation/Outside Mirror Description and Operation (Power Mirrors))
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
Scan Tool References
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Verification
Command the left and right outside mirror to move up, down, left and right using the mirror directional switch. The mirror should move in the
commanded direction.
Circuit/System Testing
1. Ignition OFF, disconnect the X3 harness connector at the appropriate door module.
2. Ignition ON, verify a test lamp does not illuminate between the following control circuit terminals and ground:
* Control circuit terminal 1
* Control circuit terminal 2
* Control circuit terminal 6
瀚慖f the test lamp illuminates, test the appropriate control circuit for a short to voltage.
3. Ignition OFF, test for infinite resistance between the following control circuits and ground:
* Control circuit terminal 1
* Control circuit terminal 2
* Control circuit terminal 6
瀚慖f less the specified value, test the appropriate control circuit for a short to ground.
4. Test for 40-100 ohms between the control circuit terminal 1 and the control circuit terminal 6.
瀚慖f not within the specified range, test both control circuits for an open/high resistance. If the circuits test normal, test or replace the
rearview mirror.
5. Test for 40-100 ohms between the control circuit terminal 2 and the control circuit terminal 6.
瀚慖f not within the specified range, test both control circuit for an open/high resistance. If the circuits test normal, test or replace the
rearview mirror.
6. If all circuits test normal, replace the door module.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Outside Rearview Mirror Motor Replacement (See: Body and Frame/Mirrors/Power Mirror Motor/Service and Repair)
* Control Module References (See: Testing and Inspection/Programming and Relearning) for DDM or PDM replacement, setup, and
Mercedes Benz Diagnostic and Repair Information ,Wiring Diagrams. DTC. TSB. Types: TSB, DTC, Wiring Diagrams, OEM Procedures. Trusted by more than 400,000 technicians. OEM accurate fix for faster repairs. Repair Procedures and Labor Times. Factory Auto Repair info. Request A Demo Today. Factory-Correct Diagrams. Factory Part Numbers. Maintenance Schedules. Repair Procedures. Labor Times. Types: TSB, DTC.Mercedes,Mercedes,Benz,Mercedes-Benz UK,A,Class,B,Class,C,Class,E,Class,CLA,CLS,G,Class,GLA,A
Saturday, September 5, 2020
2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 472
Subscribe to:
Post Comments (Atom)
No comments:
Post a Comment