2010 Cadillac CTS Sedan AWD V6-3.0L Page 1800

2010 Cadillac CTS Sedan AWD V6-3.0L Page 1800

2. Ignition ON, verify that a test lamp illuminates between the ignition circuit terminal 1 and ground.

瀚慖f the test lamp does not illuminate, test the circuit for a short to ground or an open/high resistance. If the circuit tests normal and the

ignition circuit fuse is open, test all the components connected to the ignition circuit and replace as necessary.

3. Connect a DMM, set on the diode setting, between the control circuit terminal 2 and ground. The voltage should be greater than 2 V.

瀚慖f the DMM displays OL, test the control circuit for a short to voltage or an open/high resistance. If the circuit/connections test normal,

replace the Engine Control Module.

瀚慖f less than the specified value, test the control circuit for a short to ground. If the circuit tests normal, replace the Engine Control Module.

4. Command the Camshaft Position Actuator Solenoid Valve ON and OFF with a scan tool. The DMM should transition from greater than 2 V

when commanded OFF to less than 1 V, when commanded ON.

瀚慖f the circuit voltage does not correspond to the specified values, replace the Engine Control Module.

5. If all circuits/connections test normal, test or replace the appropriate Camshaft Position Actuator Solenoid Valve.

Component Testing

1. Ignition OFF, disconnect the harness connector at the appropriate Camshaft Position Actuator Solenoid Valve.

2. Test for 7-12 ohm between the control terminal 2 and the ignition terminal 1 of the Camshaft Position Actuator Solenoid Valve.

瀚慖f not within the specified range, replace the Camshaft Position Actuator Solenoid Valve.

3. Test for infinite resistance between each terminal and the Camshaft Position Actuator Solenoid Valve housing.

瀚慖f not the specified value, replace the Camshaft Position Actuator Solenoid Valve.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Camshaft Position Actuator Solenoid Valve Solenoid Replacement - Bank 1 (Right Side) Intake (See: Engine, Cooling and

Exhaust/Engine/Actuators and Solenoids - Engine/Variable Valve Timing Solenoid/Service and Repair/Camshaft Position Actuator Solenoid

Valve Solenoid Replacement - Bank 1 (Right Side) Intake)

* Camshaft Position Actuator Solenoid Valve Solenoid Replacement - Bank 1 (Right Side) Exhaust (See: Engine, Cooling and

Exhaust/Engine/Actuators and Solenoids - Engine/Variable Valve Timing Solenoid/Service and Repair/Camshaft Position Actuator Solenoid

Valve Solenoid Replacement - Bank 1 (Right Side) Exhaust)

* Camshaft Position Actuator Solenoid Valve Solenoid Replacement - Bank 2 (Left Side) Intake (See: Engine, Cooling and

Exhaust/Engine/Actuators and Solenoids - Engine/Variable Valve Timing Solenoid/Service and Repair/Camshaft Position Actuator Solenoid

Valve Solenoid Replacement - Bank 2 (Left Side) Intake)

* Camshaft Position Actuator Solenoid Valve Solenoid Replacement - Bank 2 (Left Side) Exhaust (See: Engine, Cooling and

Exhaust/Engine/Actuators and Solenoids - Engine/Variable Valve Timing Solenoid/Service and Repair/Camshaft Position Actuator Solenoid

Valve Solenoid Replacement - Bank 2 (Left Side) Exhaust)

* Control Module References (See: Testing and Inspection/Programming and Relearning)for Engine Control Module replacement, setup, and

programming

P2092

DTC P0010, P0013, P0020, P0023, P2088, P2089, P2090, P2091, P2092, P2093, P2094, or P2095 (Without LF1)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions)provides an overview of each diagnostic category.

DTC Descriptors

DTC P0010

- Intake Camshaft Position Actuator Solenoid Valve Control Circuit Bank 1

DTC P0013

- Exhaust Camshaft Position Actuator Solenoid Valve Control Circuit Bank 1