2010 Cadillac Truck Escalade RWD V8-6.2L Page 2469

2010 Cadillac Truck Escalade RWD V8-6.2L Page 2469

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

Ignition ON, verify the scan tool Fuel Tank Level Remaining parameter is between 4-98 percent.

Circuit/System Testing

1. Ignition OFF, disconnect the harness connector at the secondary fuel level sensor.

2. Ignition OFF, test for less than 1 ohm between the low reference circuit terminal B and ground.

瀚慖f greater than the specified range, test the low reference circuit for a short to voltage or an open/high resistance. If the circuit tests

normal, replace the ECM.

3. Ignition ON, install a 3 A fused jumper wire between the secondary signal circuit terminal C and the low reference circuit terminal B. Verify

the scan tool Fuel Tank Level Remaining parameter display is greater than 98 percent.

瀚慖f less than the specified range, test the secondary signal circuit for a short to voltage or an open/high resistance. If the circuit tests

normal, replace the ECM.

4. If all circuits test normal, test or replace the secondary fuel level sensor.

Component Testing

1. Ignition OFF, remove the secondary fuel level sender.

2. While sweeping the fuel level sensor through its full range of motion, test for a minimum resistance value of less than 41 ohm and a

maximum value greater than 119 ohm between the secondary signal terminal B and the low reference terminal C.

瀚慖f not within the specified range, replace the secondary fuel level sensor.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Fuel Level Sensor Replacement (See: Powertrain Management/Computers and Control Systems/Fuel Level Sensor/Service and Repair) for

the 6.0L (LFA) engine

* Fuel Level Sensor Replacement (2500 - 98.4L (26 gal) Tank - Front) (See: Powertrain Management/Computers and Control Systems/Fuel

Level Sensor/Service and Repair/Fuel Level Sensor Replacement (2500 - 98.4L (26 Gal) Tank - Front))Fuel Level Sensor Replacement

(2500 - 43.5L (11.5 gal) Tank - Rear) (See: Powertrain Management/Computers and Control Systems/Fuel Level Sensor/Service and

Repair/Fuel Level Sensor Replacement (2500 - 43.5L (11.5 Gal) Tank - Rear))Fuel Level Sensor Replacement (1500 Series) (See:

Powertrain Management/Computers and Control Systems/Fuel Level Sensor/Service and Repair/Fuel Level Sensor Replacement (1500

Series))Fuel Level Sensor Replacement (1500 Series w/E85) (See: Powertrain Management/Computers and Control Systems/Fuel Level

Sensor/Service and Repair/Fuel Level Sensor Replacement (1500 Series w/E85)) for the 4.8L, 5.3L, 6.0L, 6.2L, or 7.0L engine

* Control Module References (See: Testing and Inspection/Programming and Relearning) for the ECM replacement, programming and setup

P2101

DTC P1516, P2101, P2119, or P2176

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.