Sunday, March 8, 2020

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 2908

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 2908

3. Perform the Control Solenoid Valve and Transmission Control Module Assembly Inspection (See: Transmission and Drivetrain/Automatic

Transmission/Transaxle/Testing and Inspection/Component Tests and General Diagnostics/2ML70 - Automatic Transmission/Control

Solenoid Valve and Transmission Control Module Assembly Inspection) to verify control solenoid valve assembly condition.

4. Perform the Control Solenoid Valve and Transmission Control Module Assembly Solenoid Performance Test (See: Transmission and

Drivetrain/Automatic Transmission/Transaxle/Testing and Inspection/Component Tests and General Diagnostics/2ML70 - Automatic

Transmission/Control Solenoid Valve and Transmission Control Module Assembly Solenoid Performance Test) to verify control solenoid

valve assembly function.

5. Inspect the control valve upper body assembly for sticking valves, damage, scored bores, or debris.

瀚慖f a concern is found in the valve body, repair or replace the valve body as necessary.

Component Testing

* Perform the Control Solenoid Valve and Transmission Control Module Assembly Inspection (See: Transmission and Drivetrain/Automatic

Transmission/Transaxle/Testing and Inspection/Component Tests and General Diagnostics/2ML70 - Automatic Transmission/Control

Solenoid Valve and Transmission Control Module Assembly Inspection).

* Perform the Control Solenoid Valve and Transmission Control Module Assembly Solenoid Performance Test (See: Transmission and

Drivetrain/Automatic Transmission/Transaxle/Testing and Inspection/Component Tests and General Diagnostics/2ML70 - Automatic

Transmission/Control Solenoid Valve and Transmission Control Module Assembly Solenoid Performance Test).

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Control Solenoid Valve and Transmission Control Module Assembly Replacement (See: Transmission and Drivetrain/Automatic

Transmission/Transaxle/Extension Housing/Service and Repair/Control Solenoid Valve and Transmission Control Module Assembly

Replacement) for control valve body repair or replacement.

* Control Module References (See: Testing and Inspection/Programming and Relearning) for Q8 control solenoid valve assembly

replacement, setup, and programming.

6L50/6L80/6L90 - Automatic Transmission

DTC P2714 or P2715

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC P2714

- Clutch Pressure Control (PC) Solenoid 4 - Stuck Off

DTC P2715

- Clutch Pressure Control (PC) Solenoid 4 - Stuck On

Circuit/System Description

The clutch pressure control (PC) solenoid 4 is part of the control solenoid valve assembly, which has no serviceable parts. The PC solenoid 4

regulates transmission fluid pressure to the 2-6 clutch regulator valve which controls pressure to the 2-6 clutch. The TCM calculates gear ratio

based on the RPM signals from the input speed sensor (ISS) and the output speed sensor (OSS). The TCM compares the expected transmission gear

ratio to the calculated gear ratio for each commanded gear.

Conditions for Running the DTC

P2714

* DTCs P0716, P0717, P0722, P0723, P1825, or P1915 are not set.

* The transmission input shaft speed is greater than 60 RPM.

* 2-6 clutch is commanded ON.

P2715

* DTCs P0716, P0717, P0722, P0723, P1825, or P1915 are not set.

* The transmission output shaft speed is greater than 200 RPM.

* 2-6 clutch is commanded OFF.

No comments:

Post a Comment