2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 2675

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 2675

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Control Solenoid Valve and Transmission Control Module Assembly Replacement (See: Transmission and Drivetrain/Automatic

Transmission/Transaxle/Extension Housing/Service and Repair/Control Solenoid Valve and Transmission Control Module Assembly

Replacement).

* Hybrid Low, 1-2 Clutch Piston Removal (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Service and

Repair/Overhaul/2ML70 - Automatic Transmission/24. Hybrid Low, 1-2 Clutch Piston Removal) and Hybrid Low, 1-2 Clutch Piston

Installation (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Service and Repair/Overhaul/2ML70 - Automatic

Transmission/31. Hybrid Low, 1-2 Clutch Piston Installation) for low and hybrid low, 1-2 clutch assembly repair or replacement.

* Control Module References (See: Testing and Inspection/Programming and Relearning) for control solenoid valve assembly replacement,

setup, and programming.

6L50/6L80/6L90 - Automatic Transmission

DTC P0796 or P0797

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC P0796

- Clutch Pressure Control (PC) Solenoid 3 - Stuck Off

DTC P0797

- Clutch Pressure Control (PC) Solenoid 3 - Stuck On

Circuit/System Description

The clutch pressure control (PC) solenoid 3 is part of the control solenoid valve assembly, which has no serviceable parts. The PC solenoid 3

regulates transmission fluid pressure to the CBR1/C 4-5-6 clutch regulator valve which controls pressure to the 4-5-6 clutch. The TCM calculates

gear ratio based on the RPM signals from the input speed sensor (ISS) and the output speed sensor (OSS). The TCM compares the expected

transmission gear ratio to the calculated gear ratio for each commanded gear.

Conditions for Running the DTC

P0796

* DTCs P0716, P0717, P0722, P0723, P182E or P1915 are not set.

* High side driver (HSD) is enabled.

* The throttle position is 10 percent or greater.

* The transmission input shaft speed is 60 RPM or greater.

* Low and reverse/4-5-6 clutch is commanded ON.

P0797

* DTCs P0716, P0717, P0722, P0723, P182E or P1915 are not set.

* High side driver (HSD) is enabled.

* The throttle position is 10 percent or greater.

* The transmission output shaft speed is 200 RPM or greater.

* Low and reverse/4-5-6 clutch is commanded OFF.

Conditions for Setting the DTC

P0796

The TCM detects an incorrect on-coming clutch gear ratio, or flare, when the low and reverse/4-5-6 clutch is commanded ON for 2 seconds and the

transmission input shaft speed is 75 RPM or greater from the anticipated input shaft speed.

P0797

The TCM detects an incorrect off-going clutch gear ratio, or tie-up, when the low and reverse/4-5-6 clutch is commanded OFF for 2 seconds and