Monday, February 24, 2020

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 2590

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 2590

DTC P0667, P0668, or P0669

* DTCs P0667, P0716, P0717, P0722, or P0723 are not set.

* The TCM internal temperature is between -55掳C and +150掳C (-67掳F and +302掳F).

* The engine speed is 500 RPM or more for 5 seconds.

* The ignition voltage is 8.6V or greater.

Conditions for Setting the DTC

P0667 - Condition 1

* Vehicle speed is 8 km/h (5 mph) or greater for 5 minutes.

* Torque converter clutch (TCC) slip speed is greater than 150 RPM for 3 minutes.

* The TCM internal temperature is between -55掳C and +21掳C (-67掳F and +70掳F).

* The TCM internal temperature has changed by less than 2.0掳C (3.6掳F) in 2 minutes.

* The transmission fluid temperature (TFT) is greater than 70掳C (158掳F).

* The TFT has increased by 55掳C (99掳F) since startup.

Condition 2

* Vehicle speed is 8 km/h (5 mph) or greater for 5 minutes.

* TCC slip speed is greater than 120 RPM for 5 minutes.

* The TCM internal temperature is between 120-150掳C (248-302掳F).

* The TCM internal temperature has changed by less than 2.0掳C (3.6掳F) in 2 minutes.

* The TFT is 70掳C (158掳F) or greater.

* The TFT has increased by 55掳C (99掳F) since startup.

Condition 3

The TCM internal temperature changes by 20掳C (36掳F) or greater 14 times over 7 seconds.

P0668

The TCM internal temperature is 249掳C (480掳F) or greater for 4 seconds or more.

P0669

The TCM internal temperature is -249掳C (-416掳F) or greater for 4 seconds or more.

Action Taken When the DTC Sets

* DTCs P0667, P0668, and P0669 are Type C DTCs.

* The TCM allows the vehicle to operate in transmission protection mode.

Conditions for Clearing the DTC

DTCs P0667, P0668, and P0669 are Type C DTCs.

Diagnostic Aids

During a road test, the TCM temperature should steadily increase to a normal operating temperature, and then stabilize.

Reference Information

Schematic Reference

Automatic Transmission Controls Schematics (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Diagrams)

Connector End View Reference

* Component Connector End Views (See: Diagrams/Connector Views)

* Inline Harness Connector End Views (See: Power and Ground Distribution/Multiple Junction Connector/Diagrams)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

No comments:

Post a Comment