2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 2677

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 2677

* J 21867 - Pressure Gauge

For equivalent regional tools, refer to Special Tools (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Tools and

Equipment/6L45/6L50/6L80/6L90 - Automatic Transmission).

Circuit/System Verification

Note: If other DTCs are set, diagnose those DTCs first.

1. Engine idling in Park, with parking brake applied and drive wheels chocked.

2. Perform the Transmission Fluid Level and Condition Check (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing

and Inspection/Initial Inspection and Diagnostic Overview/6L45/6L50/6L80/6L90 - Automatic Transmission/Transmission Fluid Level and

Condition Check) to verify correct fluid level and condition.

3. Monitor the Transmission Fluid Pressure (TFP) switch 5 with a scan tool. Place the gear select lever in Park, Reverse, and Neutral range.

Verify the TFP switch 5 parameter states are correct for Park, Reverse, and Neutral. Refer to Transmission Fluid Pressure Switch Logic (

See: Specifications/Mechanical Specifications/Automatic Transmission/Transaxle/System Specifications/6L45/6L50/6L80/6L90 - Automatic

Transmission/Transmission Fluid Pressure Switch Logic).

4. Place the gear select lever in Drive range. Command the shift transmission with a scan tool through all forward ranges. Verify the TFP switch

5 parameter states are correct for all forward ranges. Refer to Transmission Fluid Pressure Switch Logic (See: Specifications/Mechanical

Specifications/Automatic Transmission/Transaxle/System Specifications/6L45/6L50/6L80/6L90 - Automatic Transmission/Transmission

Fluid Pressure Switch Logic).

5. Engine idling in Park, verify with a scan tool the Transmission ISS/OSS supply voltage test status parameter displays OK.

6. Engine idling in Park. Observe the Transmission ISS parameter on the scan tool, while varying the engine speed. The Transmission ISS

parameter should vary with engine speed and not drop out.

7. Operate the vehicle at 16-32 km/h (10-20 mph) while observing the Transmission OSS parameter on the scan tool. The Transmission OSS

parameter should vary with the vehicle speed and not drop out.

Note: Perform a scan tool snapshot, during the road test.

8. Perform the Road Test (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing and Inspection/Initial Inspection and

Diagnostic Overview/6L45/6L50/6L80/6L90 - Automatic Transmission/Road Test). Verify the transmission operation performs as indicated

in the road test instructions.

9. Review the scan tool snapshot data. Verify the following transmission data parameters display the correct values for each gear range:

* Transmission ISS

* Transmission OSS

* PC Solenoid 3

* TFP Switch 5

10. Operate the vehicle within the Condition for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Perform the Line Pressure Check (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing and Inspection/Component

Tests and General Diagnostics/6L45/6L50/6L80/6L90 - Automatic Transmission/Line Pressure Check). Verify the transmission line

pressures are within the specified ranges.

瀚慖f not within the specified ranges, refer to Fluid Pressure High or Low (See: Transmission and Drivetrain/Automatic

Transmission/Transaxle/Testing and Inspection/Symptom Related Diagnostic Procedures/6L45/6L50/6L80/6L90 - Automatic

Transmission/Fluid Pressure High or Low).

2. Ignition OFF, remove the Q8 control solenoid valve assembly. Refer to Control Solenoid Valve and Transmission Control Module Assembly

Replacement (See: Powertrain Management/Transmission Control Systems/Actuators and Solenoids - Transmission and

Drivetrain/Actuators and Solenoids - A/T/Shift Solenoid/Service and Repair).

3. Perform the Control Solenoid Valve and Transmission Control Module Assembly Solenoid Performance Test (See: Transmission and

Drivetrain/Automatic Transmission/Transaxle/Testing and Inspection/Component Tests and General Diagnostics/6L45/6L50/6L80/6L90 -

Automatic Transmission/Control Solenoid Valve and Transmission Control Module Assembly Solenoid Performance Test). Test all solenoids

on the Q8 control solenoid valve assembly. A pressure change should occur for each solenoid valve.

瀚慖f the Q8 control solenoid valve assembly does not pass the performance test, replace the Q8 control solenoid valve assembly.

4. Listed in the chart below, are conditions for each component that could set DTC P0796 or P0797. Carefully inspect each component for that

condition. Repair or replace as necessary.