2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 2656

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 2656

Gear 3, 4, or EVT 2 is commanded.

Conditions for Setting the DTC

The transmission control module detects shift solenoid valve 2 is OFF when commanded ON.

Action Taken When the DTC Sets

P0756 is a Type B DTC.

Conditions for Clearing the DTC

P0756 is a Type B DTC.

Reference Information

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Circuit/System Verification

1. Verify that P0721, P0722, P0723, P0966, P0967, P0969, P0970, P0971, P0973, P0974, P0976, P0977, P2720, P2721, P2728, P2729, or

P2730 is not set.

瀚慖f any of the DTCs are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code

Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle).

2. Perform the Transmission Fluid Level and Condition Check (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing

and Inspection/Symptom Related Diagnostic Procedures/2ML70 - Automatic Transmission/Transmission Fluid Level and Condition Check).

3. Perform the Line Pressure Check (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing and Inspection/Component

Tests and General Diagnostics/2ML70 - Automatic Transmission/Line Pressure Check).

4. Perform the Control Solenoid Valve and Transmission Control Module Assembly Inspection (See: Transmission and Drivetrain/Automatic

Transmission/Transaxle/Testing and Inspection/Component Tests and General Diagnostics/2ML70 - Automatic Transmission/Control

Solenoid Valve and Transmission Control Module Assembly Inspection).

5. Perform the Control Solenoid Valve and Transmission Control Module Assembly Solenoid Performance Test (See: Transmission and

Drivetrain/Automatic Transmission/Transaxle/Testing and Inspection/Component Tests and General Diagnostics/2ML70 - Automatic

Transmission/Control Solenoid Valve and Transmission Control Module Assembly Solenoid Performance Test).

瀚慖f the shift solenoid 2 is found to be leaking or stuck OFF, replace the control solenoid valve assembly.

瀚慖f the control solenoid valve assembly tests normal, inspect the valve body and hydraulic circuits for a leak or a stuck valve.

6. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Control Module References (See: Testing and Inspection/Programming and Relearning) for control solenoid valve assembly replacement,

setup, and programming.

* Control Valve Upper Body Replacement (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Valve Body/Service and

Repair/2ML70 - Automatic Transmission) for control valve body repair or replacement.

P0757

DTC P0757

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.