2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 638
dimming supply circuit to the components on that circuit.
Conditions for Running the DTC
* Battery Voltage be between 9-16 V.
* The ignition is ON.
Conditions for Setting the DTC
The BCM, driver door switch, and passenger door switch detect a short to voltage, short to ground, or an open on the LED dimming supply circuit.
Action Taken When the DTC Sets
The BCM, driver door switch, and passenger door switch will cease attempts to dim or illuminate the LED lamps.
Conditions for Clearing the DTC
* The conditions for setting the DTC are no longer present.
* A history DTC clears after 100 malfunction-free ignition cycles.
* The BCM receives the clear code command from the scan tool.
Reference Information
Schematic Reference
Interior Lights Dimming Schematics (See: Diagrams/Electrical Diagrams/Lighting and Horns/System Diagram/Interior Lights Dimming
Schematics)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Interior Lighting Systems Description and Operation (See: Lighting and Horns/Description and Operation/Interior Lighting Systems Description
and Operation)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Testing
Note: Each back lighted component may need to be disconnected to isolate a short to voltage or short to ground. Use the schematic to identify the
following:
* Back lighted components the vehicle is equipped with.
* Component locations on the back lighting dimming control circuit
* Each component's control and ground circuit terminals
1. Ignition OFF, disconnect the harness connector at any component with inoperative backlighting.
2. Ignition OFF, scan tool disconnected, interior lamps OFF, doors CLOSED, test for less than 5 ohm between the ground circuit and ground.
瀚慖f greater than the specified value, test the ground circuit for an open/high resistance.
3. Connect a test lamp between the control circuit and ground.
4. Command the Incandescent Dimming Control ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between
the commanded states.
瀚慖f the test lamp is always OFF, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace
the BCM.
瀚慖f the test lamp is always ON, test the control circuit for a short to voltage. If the circuit tests normal, replace the BCM.
Mercedes Benz Diagnostic and Repair Information ,Wiring Diagrams. DTC. TSB. Types: TSB, DTC, Wiring Diagrams, OEM Procedures. Trusted by more than 400,000 technicians. OEM accurate fix for faster repairs. Repair Procedures and Labor Times. Factory Auto Repair info. Request A Demo Today. Factory-Correct Diagrams. Factory Part Numbers. Maintenance Schedules. Repair Procedures. Labor Times. Types: TSB, DTC.Mercedes,Mercedes,Benz,Mercedes-Benz UK,A,Class,B,Class,C,Class,E,Class,CLA,CLS,G,Class,GLA,A
Tuesday, December 3, 2019
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 638
Subscribe to:
Post Comments (Atom)
No comments:
Post a Comment