2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 645
Conditions for Clearing the DTC
* The condition responsible for setting the DTC no longer exists.
* You issue a scan tool CLEAR DTCs command.
* A history DTC will clear once 100 consecutive malfunction-free ignition cycles have occurred.
Reference Information
Schematic Reference
Headlights/Daytime Running Lights (DRL) Schematics (See: Diagrams/Electrical Diagrams/Lighting and Horns/System
Diagram/Headlights/Daytime Running Lights (DRL) Schematics)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Exterior Lighting Systems Description and Operation (See: Lighting and Horns/Description and Operation/Exterior Lighting Systems Description
and Operation)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Testing
1. Ignition OFF, disconnect the harness connector at the ambient light sensor.
2. Test for less than 5.0 ohm between the ground circuit listed below and ground.
* Ambient Light Sensor terminal C - CJ2
* Ambient Light Sensor terminal B - w/o CJ2
瀚慖f greater than the specified range, test the ground circuit for an open/high resistance.
3. Ignition ON, verify the scan tool Ambient Light Sensor parameter is greater than 4.5 V.
瀚慖f less than the specified range, test the signal circuit for a short to ground. If the circuit tests normal, replace the BCM.
4. Install a 3 A fused jumper wire between the signal circuit terminal listed below and the low reference circuit terminal listed below. Verify the
scan tool Ambient Light Sensor parameter is less than 1.0 V.
* Ambient Light Sensor terminals A to B - w/o CJ2
* Ambient Light Sensor terminals D to C - CJ2
瀚慖f greater than the specified range, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal,
replace the BCM.
5. If all circuits test normal, test or replace the ambient light sensor.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Ambient Light Sensor Replacement (See: Lighting and Horns/Ambient Light Sensor/Service and Repair)
* Control Module References (See: Testing and Inspection/Programming and Relearning) for BCM replacement, setup, and programming
Mercedes Benz Diagnostic and Repair Information ,Wiring Diagrams. DTC. TSB. Types: TSB, DTC, Wiring Diagrams, OEM Procedures. Trusted by more than 400,000 technicians. OEM accurate fix for faster repairs. Repair Procedures and Labor Times. Factory Auto Repair info. Request A Demo Today. Factory-Correct Diagrams. Factory Part Numbers. Maintenance Schedules. Repair Procedures. Labor Times. Types: TSB, DTC.Mercedes,Mercedes,Benz,Mercedes-Benz UK,A,Class,B,Class,C,Class,E,Class,CLA,CLS,G,Class,GLA,A
Tuesday, December 3, 2019
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 645
Subscribe to:
Post Comments (Atom)
No comments:
Post a Comment