Sunday, November 17, 2019

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1112

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1112



the ignition was turned OFF last ignition cycle.



* DTCs P0137 runs continuously once the above conditions are met.



P0138 and P0140



* The HO2S 2 is at operating temperature for greater than 30 seconds.



* The engine is operating for greater than 1 second.



* The ignition voltage is greater than 10 volts.



* DTCs P0138 runs continuously once the above conditions are met for greater than 5 seconds.



* DTCs P0140 runs continuously once the above conditions are met for greater than 60 seconds.



Conditions for Setting the DTC



P0137



The ECM detects that a secondary HO2S signal voltage is less than 60 mV for greater than 1 seconds of for a cumulative of 10 seconds.



P0138



The ECM detects that the HO2S signal voltage is greater than 1,150 mV for greater than 1 seconds or for a cumulative of 10 seconds.



P0140



* The ECM detects that the HO2S 2 signal voltage is between 401-519 mV, when the calculated exhaust temperature is less than 800掳C (1,472



掳F).



* The ECM detects that the HO2S 2 signal voltage is between 401-548 mV, when the calculated exhaust temperature is greater than 800掳C



(1,472掳F).



* The ECM detects that the measured internal resistance of the HO2S is greater than 40,000 ohm, when the calculated exhaust temperature is



greater than 450掳C (802掳F).



* The ECM detects any one of the above conditions for greater than 1 second or for a cumulative of 10 seconds.



Action Taken when the DTC Sets



DTCs P0137, P0138, and P0140 are Type B DTCs.



Conditions for Clearing the MIL/DTC



DTCs P0137, P0138, and P0140 are Type B DTCs.



Reference Information



Schematic Reference



Engine Controls Schematics (LAU) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics



(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)



Connector End View Reference



Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)



Electrical Information Reference



* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit



Testing/Circuit Testing)



* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic



Procedures/Connector Repairs/Connector Repairs)



* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General



Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)



* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring



Repairs/Wiring Repairs)



DTC Type Reference



Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code



(DTC) Type Definitions)



Scan Tool Reference



Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information



Circuit/System Verification



1. Engine idling, observe the scan tool HO2S 2 voltage parameter. The reading should fluctuate above and below the range of 350-550 mV.



2. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the



conditions that you observed from the Freeze Frame/Failure Records data.

No comments:

Post a Comment