Tuesday, November 19, 2019

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1393

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1393



The ECM detects the voltage on the EVAP canister vent valve control circuit is less than 2.6 volts when the driver is commanded OFF. The



condition is present for greater than 4 seconds or for a cumulative of 30 seconds.



P0499



The ECM detects the voltage on the EVAP canister vent valve control circuit is greater than 4.6 volts when the driver is commanded ON. The



condition is present for greater than 4 seconds or for a cumulative of 30 seconds.



Action Taken When the DTC Sets



* DTC P0449, P0498 and P0499 are Type B DTCs.



* The EVAP system will only purge during open loop.



Conditions for Clearing the DTC



DTC P0449, P0498 and P0499 are Type B DTCs.



Reference Information



Schematic Reference



Engine Controls Schematics (LAU) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics



(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)



Connector End View Reference



Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)



Description and Operation



Evaporative Emission Control System Description (See: Powertrain Management/Computers and Control Systems/Description and



Operation/Evaporative Emission Control System Description)



Electrical Information Reference



* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit



Testing/Circuit Testing)



* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic



Procedures/Connector Repairs/Connector Repairs)



* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General



Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)



* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring



Repairs/Wiring Repairs)



DTC Type Reference



Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code



(DTC) Type Definitions)



Scan Tool Reference



Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information



Circuit/System Verification



1. Command the EVAP vent solenoid valve ON and OFF with the scan tool. An audible click should be heard when changing between the



commanded states.



2. Start the engine, observe the DTC information with a scan tool. DTC P0449, P0498, or P0499 should not set.



3. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the



conditions that you observed from the Freeze Frame/Failure Records data.



Circuit/System Testing



1. Ignition OFF, disconnect the harness connector at the EVAP vent solenoid valve.



2. Ignition ON, verify that a test lamp illuminates between the ignition voltage circuit terminal A and ground.



瀚慖f the test lamp does not illuminate, test the ignition voltage circuit for a short to ground or an open/high resistance. If the circuit tests



normal and the ignition voltage circuit fuse is open, test all components connected to the ignition voltage circuit and replace as necessary.



3. Ignition OFF, connect a test lamp between the control circuit terminal B and the ignition voltage circuit terminal A.



Important: The control circuit for the EVAP vent solenoid valve is pulled-up to voltage within the ECM, 2.6-4.6 volts on the control

No comments:

Post a Comment