2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 288

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 288

Actions Taken When the DTC Sets

* The low beam headlamps are always ON in the AUTO position. The headlamp switch operates in all positions other than AUTO. The AUTO

headlamp defeat is inoperative.

* The low beam headlamps are always ON. The BCM disregards all headlamp switch inputs.

Conditions for Clearing the DTC

* The condition responsible for setting the DTC no longer exists.

* A history DTC will clear once 100 consecutive malfunction-free ignition cycles have occurred.

Reference Information

Schematic Reference

Headlights/Daytime Running Lights (DRL) Schematics (See: Diagrams/Electrical Diagrams/Lighting and Horns/System

Diagram/Headlights/Daytime Running Lights (DRL) Schematics)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Description and Operation

Exterior Lighting Systems Description and Operation (See: Lighting and Horns/Description and Operation/Exterior Lighting Systems Description

and Operation)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Testing

1. Ignition OFF, disconnect the X2 harness connector at the BCM.

2. Connect a test lamp between B+ and the signal circuit terminal 17.

3. Turn the headlamp switch between the AUTO and AUTO disable positions. The test lamp should turn ON and OFF as the switch is cycled.

瀚慖f the test lamp is always OFF, test the signal circuit for a short to voltage or an open/high resistance. If the circuit test normal, replace the

headlamp and panel dimmer switch.

瀚慖f the test lamp is always ON, test the signal circuit for a short to ground. If the circuit test normal, replace the headlamp and panel

dimmer switch.

4. Connect a test lamp between B+ and the signal circuit terminal 3.

5. Turn the headlamp switch to the ON and OFF positions. The test lamp should turn ON and OFF as the switch is cycled.

瀚慖f the test lamp is always OFF, test the signal circuit for a short to voltage or an open/high resistance. If the circuit test normal, replace the

headlamp and panel dimmer switch.

瀚慖f the test lamp is always ON, test the signal circuit for a short to ground. If the circuit test normal, replace the headlamp and panel

dimmer switch.

6. If all circuits test normal, replace the BCM.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Headlamp Switch Replacement (Cadillac) (See: Lighting and Horns/Headlamp/Headlamp Switch/Service and Repair/Headlamp Switch

Replacement (Cadillac))Headlamp Switch Replacement (Except Cadillac) (See: Lighting and Horns/Headlamp/Headlamp Switch/Service

and Repair/Headlamp Switch Replacement (Except Cadillac))

* Control Module References (See: Testing and Inspection/Programming and Relearning) for BCM replacement, setup, and programming