2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 202
1. Ignition OFF, disconnect the harness connector at the appropriate B88 seat position sensor.
2. Test for less than 10 ohm between the low reference circuit terminal 1 and ground.
瀚慖f greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the K36
SDM.
3. Ignition ON, test for 4-9 V between the signal circuit terminal 2 and ground.
瀚慖f less than the specified value, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace
the K36 SDM.
瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the K36 SDM.
4. If all circuits test normal, replace the B88 seat position sensor.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Inflatable Restraint Seat Position Sensor Replacement (with HP2) (See: Restraints and Safety Systems/Air Bag Systems/Seat Position
Sensor/Service and Repair)Inflatable Restraint Seat Position Sensor Replacement (without HP2) (See: Restraints and Safety Systems/Air
Bag Systems/Seat Position Sensor/Service and Repair)
* SIR/SRS Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Wiring Repairs/SIR/SRS Wiring Repairs)
* Control Module References (See: Testing and Inspection/Programming and Relearning)for SDM replacement, setup, and programming
B0080
DTC B0079 or B0080
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions)provides an overview of each diagnostic category
DTC Descriptors
DTC B0079 01
- Driver Seat Position Sensor Circuit Short to Battery
DTC B0079 02
- Driver Seat Position Sensor Circuit Short to Ground
DTC B0079 04
- Driver Seat Position Sensor Circuit Open
DTC B0079 05
- Driver Seat Position Sensor Circuit High Voltage or Open
DTC B0079 06
- Driver Seat Position Sensor Circuit Low Voltage or Open
DTC B0079 08
- Driver Seat Position Sensor Circuit Performance-Signal Invalid
DTC B0079 0C
- Driver Seat Position Sensor Circuit Low Current
DTC B0080 01
- Passenger Seat Position Sensor Circuit Short to Battery
DTC B0080 02
- Passenger Seat Position Sensor Circuit Short to Ground
DTC B0080 04
- Passenger Seat Position Sensor Circuit Open
Mercedes Benz Diagnostic and Repair Information ,Wiring Diagrams. DTC. TSB. Types: TSB, DTC, Wiring Diagrams, OEM Procedures. Trusted by more than 400,000 technicians. OEM accurate fix for faster repairs. Repair Procedures and Labor Times. Factory Auto Repair info. Request A Demo Today. Factory-Correct Diagrams. Factory Part Numbers. Maintenance Schedules. Repair Procedures. Labor Times. Types: TSB, DTC.Mercedes,Mercedes,Benz,Mercedes-Benz UK,A,Class,B,Class,C,Class,E,Class,CLA,CLS,G,Class,GLA,A
Wednesday, November 13, 2019
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 202
Subscribe to:
Post Comments (Atom)
No comments:
Post a Comment