2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 380
Conditions for Running the DTC
Ignition voltage is between 9-16 V.
Conditions for Setting the DTC
The setup for the SDM has not been completed and the SDM does not detect the correct number of sensors or deployment loops than is expected
with this calibration.
Action Taken When the DTC Sets
* The SDM requests the instrument cluster to illuminate the AIR BAG warning indicator.
* The DTC must be cleared before running the setup SDM.
* Air bag indicator will continue to flash until SDM setup procedure is complete.
Conditions for Clearing the DTC
* The condition for setting the DTC is no longer present.
* A history DTC will clear once 100 malfunction-free ignition cycles have occurred.
Diagnostic Aids
The SDM scan tool deployment loop and impact sensor data will match what the SDM has been programmed to expect to see on the vehicle. B1019
DTC will set if a deployment loop or impact sensor is added or removed from the system.
DTC B1019 will set when an open/high resistance DTC sets for a deployment loop or impact sensor. This causes mismatch between the learned and
actual components connected to the SDM.
DTC B1019 can set with no other DTCs if an unused deployment loop or impact sensor circuit is shorted to ground. This causes a mismatch
between the learned and actual components connected to the SDM.
Reference Information
Schematic Reference
* Seat Belt Schematics (See: Diagrams/Electrical Diagrams/Seat Belt Systems)
* SIR Schematics (See: Diagrams/Electrical Diagrams/Air Bag Systems)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
* Seat Belt System Description and Operation (See: Restraints and Safety Systems/Seat Belt Systems/Description and Operation)
* SIR System Description and Operation (See: Restraints and Safety Systems/Air Bag Systems/Description and Operation)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Verification
Note: DTC B1019 can set after SDM has been replaced and/or reprogrammed before the setup procedure is completed. The setup procedure
cannot be completed if DTC B1019 is set as current or history. If a short or open is detected in a deployment circuit prior to the setup procedure
being performed the SDM will set DTC B1019.
1. Ignition ON, verify no other SDM DTC are set.
瀚慖f another SDM DTC is set, diagnose those DTCs first. Refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic
Mercedes Benz Diagnostic and Repair Information ,Wiring Diagrams. DTC. TSB. Types: TSB, DTC, Wiring Diagrams, OEM Procedures. Trusted by more than 400,000 technicians. OEM accurate fix for faster repairs. Repair Procedures and Labor Times. Factory Auto Repair info. Request A Demo Today. Factory-Correct Diagrams. Factory Part Numbers. Maintenance Schedules. Repair Procedures. Labor Times. Types: TSB, DTC.Mercedes,Mercedes,Benz,Mercedes-Benz UK,A,Class,B,Class,C,Class,E,Class,CLA,CLS,G,Class,GLA,A
Tuesday, November 12, 2019
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 380
Subscribe to:
Post Comments (Atom)
No comments:
Post a Comment