2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 1270

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 1270

P0AEF, P0AF4, P0BD3, P0BD8, P0BDD, and P0BE2

The inverter phase temperature sensor is greater than 125掳C (275掳F) for 3 seconds.

P0AF0, P0AF5, P0BD4, P0BD9, P0BDE, and P0BE3

The inverter phase temperature sensor is less than -40掳C (-40掳F) for 3 seconds.

Action Taken When the DTC Sets

* DTCs P0AEE, P0AEF, P0AF0, P0AF3, P0AF4, P0AF5, P0BD2, P0BD3, P0BD4, P0BD7, P0BD8, P0BD9, P0BDC, P0BDD, P0BDE,

P0BE1, P0BE2 AND P0BE3 are Type B DTCs.

* The PIM commands the battery energy control module (BECM) to open the high voltage contactor relays.

Conditions for Clearing the DTC

DTCs P0AEE, P0AEF, P0AF0, P0AF3, P0AF4, P0AF5, P0BD2, P0BD3, P0BD4, P0BD7, P0BD8, P0BD9, P0BDC, P0BDD, P0BDE, P0BE1,

P0BE2 AND P0BE3 are Type B DTCs.

Reference Information

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Circuit/System Verification

1. Clear the DTC information.

2. Ignition OFF for 1 minute.

3. Operate the vehicle under the Conditions for Running the DTC.

4. Retest for DTCs P0AEE, P0AEF, P0AF0, P0AF3, P0AF4, P0AF5, P0BD2, P0BD3, P0BD4, P0BD7, P0BD8, P0BD9, P0BDC, P0BDD,

P0BDE, P0BE1, P0BE2 AND P0BE3.

Circuit/System Testing

Program the PIM with the latest software version and recheck for DTCs.

If the DTC resets after programming or if the PIM already contains the latest software version, replace the PIM.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

Control Module References (See: Testing and Inspection/Programming and Relearning) for PIM replacement, setup, and programming.

P0BD4

DTC P0AEE, P0AEF, P0AF0, P0AF3-P0AF5, P0BD2-P0BD4, P0BD7-P0BD9, P0BDC-P0BDE, or P0BE1-P0BE3

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptor

DTC P0AEE

- Drive Motor Inverter Temperature Sensor 1 Performance

DTC P0AEF

- Drive Motor Inverter Temperature Sensor 1 Circuit Low Voltage

DTC P0AF0

- Drive Motor Inverter Temperature Sensor 1 Circuit High Voltage