2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 483
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Retained Accessory Power Description and Operation (See: Power and Ground Distribution/Description and Operation/Retained Accessory Power
Description and Operation)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Testing
1. Ignition ON, verify DTC B1475 is set as current.
瀚慖f DTC B1475 is not set as current, operate the vehicle within the Conditions for Setting the DTC.
Note: When cycling the ignition, keep ignition OFF for 5 seconds before checking for current DTC.
2. Disconnect each of the following components one at a time. The components may be disconnected in any order. After each component is
disconnected, cycle the ignition and verify DTC B1475 remains set as current.
* Sunroof module (with RPO CF5)
* Mobile radio relay A (with RPO 9L4)
瀚慖f DTC B1475 does not remain set as current, test or replace the last component that was disconnected.
3. With all components disconnected, cycle the ignition and verify DTC B1475 is not set as current.
瀚慖f DTC B1475 remains set as current, test the accessory voltage circuit for a short to ground. If the circuit tests normal, replace the BCM.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Instrument Panel Electrical Center or Junction Block Replacement - Left Side (See: Maintenance/Fuses and Circuit Breakers/Fuse
Block/Service and Repair/Removal and Replacement/Instrument Panel Electrical Center or Junction Block Replacement - Left Side)
* Control Module References (See: Testing and Inspection/Programming and Relearning) for module replacement, setup, and programming
B1516
DTC B1516
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC B1516 08
- Battery Current Sensor Performance Signal Invalid
DTC B1516 66
- Battery Current Sensor Performance Wrong Mounting Position
Mercedes Benz Diagnostic and Repair Information ,Wiring Diagrams. DTC. TSB. Types: TSB, DTC, Wiring Diagrams, OEM Procedures. Trusted by more than 400,000 technicians. OEM accurate fix for faster repairs. Repair Procedures and Labor Times. Factory Auto Repair info. Request A Demo Today. Factory-Correct Diagrams. Factory Part Numbers. Maintenance Schedules. Repair Procedures. Labor Times. Types: TSB, DTC.Mercedes,Mercedes,Benz,Mercedes-Benz UK,A,Class,B,Class,C,Class,E,Class,CLA,CLS,G,Class,GLA,A
Wednesday, November 13, 2019
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 483
Subscribe to:
Post Comments (Atom)
No comments:
Post a Comment