2010 Cadillac Truck Escalade EXT AWD V8-6.2L Technical Service Bulletin # 12-04-21-001B Date: 130411
Drivetrain - Transfer Case Identification Information
INFORMATION
Bulletin No.: 12-04-21-001B
Date: April 11, 2013
Subject: Transfer Case Identification First Design vs. Second Design
Models:
2007-2013 Cadillac Escalade Models
2007-2013 Chevrolet Avalanche, Silverado, Suburban, Tahoe
2007-2013 GMC Sierra, Yukon, Yukon Denali
Equipped with Magna X2T Transfer Case (RPOs NQF, NQG, NQH or NP0)
Supercede:
This bulletin is being revised to add the 2013 model year, clarify the information from the previous bulletin and to add data throughout. The
document should be reviewed and treated as new information. Please discard Corporate Bulletin Number 12-04-21-001A (Section 04 -
Driveline/Axle).
The purpose of new product information is to document important product changes that occur either model year-to-model year or interim model
year.
Changes may include one or more of the following items:
- Specification changes
- New sealants and/or adhesives
- Disassembly and assembly procedure revisions
- Mechanical and diagnostic procedure revisions
- New special tools required
- Interim model year design changes
- A component comparison from the previous model year
Interim Model Year Design Change - NQF/NQG/NQH/NPO Front Output Shaft, Deflector, Seal
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 382
Interim 2012 model year, a new design front output shaft deflector (3) was implemented into production for second design NQF-HD/SHD and
NQG-HD applications. First design 2011 model year NQF and NQG applications can be identified as not having the deflector on the front output
shaft.
For service, the new design front output shaft, deflector and new design seal may be installed on current and prior model year Magna
NQF-HD/SHD, NQG-LD/HD, NQH-LD/HD and NP0 applications providing the new design front output shaft is also installed. The front output
shaft deflector is to be installed using the J 8092 - driver handle (1) and DT 50649 - seal installer (2).
The new design deflector (1) can be installed onto all current and prior model year Magna RPOs NQF, NQG, NQH and NPO applications
providing the new design front output shaft (2) is also installed. Second design front output shafts can be identified by the machined area on the OD
output end of the shaft (2). First design front output shafts can be identified by the dust boot clamp groove (3) located at the OD output end of the
shaft. The new design slinger will NOT install onto the first design shafts.
Service Parts Release Usage Change - NQH/NPO Control Actuator Levers
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 383
Light Duty (LD) 2007-2010 MP3023-NQH and 2010 MP3010-NP0 production transfer cases are built with LD control actuator levers (3 and 6)
and are used with 13 mm (0.52 in) diameter control actuator lever balls (5).
Heavy duty (HD) 2007-2010 MP3024-NQH production transfer cases are built with HD control actuator levers (3 and 6) and are used with Heavy
10 mm (0.39 in) control actuator lever balls.
When replacement of one or both of the LD control actuator levers is required, it is necessary to replace both of the levers and all three balls with
the HD components as a set. It is also necessary to re-measure and adjust clutch pack clearances as required and to perform the Transfer Case
High/Low Clutch Reset. Refer to Measuring/Adjusting Clutch Assembly Height in Transfer Case Assemble, Transfer Case Description and
Operation and Transfer Case High/Low Clutch Reset. Heavy duty (HD) components are the only parts available for service.
Interim Model Year Design Change - NQG High/Low Shift Fork, Fork Pad, and High/Low Clutch
Interim 2012 model year the High/Low shift fork, fork pad and High/Low clutch design changed. The first design forks (2) can be identified as
having three flat un-notched fork pad areas with three separate fork pads (1). The second design forks (4) can be identified as having a half-round
shaped pad area with three notches for pad orientation and installation and upper and lower half-round fork pads (3). The second design shift fork
(4) and pads (3) are the only design available for service and must be used with the second design High/Low clutch.
Interim 2012 model year the High/Low shift fork, fork pad and High/Low clutch design changed. The first design high/low clutch (1) can be
identified by having a 73 mm (2.87 in) OD rear flange (2). The second design high/low clutch (3) can be identified by having a 76 mm (2.99 in)
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 384
OD rear flange (4).
For service:
- The first design 73 mm (2.87 in) high/low clutch may NOT be used with the second design fork and pad.
- The second design 76 mm (2.99 in) high/low clutch must be used with the second design fork and fork pad.
- The second design 76 mm (2.99 in) high/low clutch may also be used with the first design fork and pad if first design fork replacement is not
required.
Interim Model Year Design Change - NQF/NQG/NQH Front Case Half Assembly, Input Shaft, Planetary Carrier High/Low Clutch
Interim 2012 model year for Magna light-duty and heavy-duty transfer case RPOs NQF / NQG / NQH, a second-design front case half assembly,
planetary internal gear, gear retaining ring, locking plate, thrust washer-front, input shaft, pilot bearing, thrust washer-rear, high/low planetary
carrier and high/low clutch were implemented into second-design assemblies.
The second-design light duty (LD), heavy duty (HD), and super-heavy duty (SHD) applications have a reduced OD dimension carrier and the
second-design planetary internal gear has a reduced ID dimension. The planetary internal gear is a press-fit non-serviceable component and must be
serviced with the front case half assembly. In service it is possible that a new or remanufactured transfer case may contain first or second-design
content.
If a second-design transfer case has been installed into a vehicle that originally contained a first-design assembly, TCCM reprogramming is not
required.
For production, the following transfer cases variations were produced:
- 2007-12i Magna LD NQG/NQH - produced with first-design content. First design service components are available. A second-design
assembly may be used for back-service in a first-design application.
- 2007-10 Magna HD NQF - produced with only first-design content. Service components are available.
- 2007-10 Magna HD NQG - produced with only first-design content. Service assemblies may contain either first or second design content.
Both first and second design service components are available.
- 2007-12i Magna HD NQH - produced with first-design content. First design service components are available. A second-design assembly
may be used for back-service in a first-design application.
- 2011-12i Magna SHD NQF/NQG - produced with first design content. First design service components are available. A second-design
assembly may be used for back-service in a first-design application.
- 2012i-13 Magna LD NQG/NQH - produced with second-design content. Second design service components are available.
- 2012i-13 Magna HD NQH - produced with second-design content. Second design service components are available.
- 2012i-13 Magna SHD NQF/NQG - produced with second-design content. Second design service components are available.
Production Assembly Breakpoints
The design level and component content of the transfer case can be determined by referencing the assembly part number located on the
identification label.
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 385
Service Parts List
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 386
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 387
Note
2007-2010 MY Heavy Duty NQF transfer case assemblies were only produced with first-design content. Service 2007-2010 MY Heavy Duty NQG
transfer case service assemblies may contain either first or second design content.
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 388
Front Case Half Identification
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 389
The first design front case half assembly can be identified as having an internal gear that is a 94 tooth design with an inside diameter (a) of 148.5
mm (5.85 in).
The second design front case half assembly can be identified as having an internal gear that is a 91 tooth design with an inside diameter (a) of 142
mm (5.59 in).
Input Shaft Identification
The first design input shaft can be identified as a 56 tooth design with an outside diameter (a) of 91.4 mm (3.60 in).
The second design input shaft can be identified as a 53 tooth design with an outside diameter (a) of 87.50 mm (3.44 in).
High/Low Planetary Carrier Assembly Identification
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 390
The first-design light-duty 3-pinion high/low planetary carrier (1) can be identified as having a 30 tooth design with an inside diameter (a) of 61.3
mm (2.41 in). In addition, the first-design carrier can also be identified by the presence of a recessed washer pocket (3) at the rear thrust washer
location.
The second-design light-duty 3-pinion high/low planetary carrier (2) can be identified as having a 29 tooth design with an inside diameter (b) of
60.2 mm (2.37 in). In addition, the second-design carrier can also be identified by the lack of a recessed washer pocket (4) at the rear thrust washer
location.
The first-design heavy-duty 5-pinion high/low planetary carrier (1) can be identified as having 5 pinions and a 30 tooth design with an inside
diameter (a) of 61.3 mm (2.41 in).
The second-design heavy-duty 6-pinion high/low planetary carrier (2) can be identified as having 6 pinions and a 29 tooth design with an inside
diameter (b) of 60.2 mm (2.37 in).
High/Low Clutch
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 391
The first design high/low clutch can be identified as having a 30 tooth design with a gear tooth outside diameter (a) of 65.50 mm (2.58 in).
The second design high/low clutch can be identified as having a 29 tooth design with a gear tooth outside diameter (a) of 63.25 mm (2.49 in).
Component Replacement - Conversion from First Design to Second Design
It is possible to repair a first-design assembly using second-design components. Refer to the parts catalog and the tables above for component part
number clarification.
Note
First-design LD components are shown in the view above.
When servicing a first-design assembly with second-design components, the following components MUST be replaced as a group:
1. Front Case Half Assembly - with internal gear and retaining ring
2. Locking Plate
3. Thrust Washer (front)
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 392
4. Input Shaft
5. Pilot Bearing
6. Thrust Washer (rear)
7. Planetary Carrier Assembly
Mercedes Benz Diagnostic and Repair Information ,Wiring Diagrams. DTC. TSB. Types: TSB, DTC, Wiring Diagrams, OEM Procedures. Trusted by more than 400,000 technicians. OEM accurate fix for faster repairs. Repair Procedures and Labor Times. Factory Auto Repair info. Request A Demo Today. Factory-Correct Diagrams. Factory Part Numbers. Maintenance Schedules. Repair Procedures. Labor Times. Types: TSB, DTC.Mercedes,Mercedes,Benz,Mercedes-Benz UK,A,Class,B,Class,C,Class,E,Class,CLA,CLS,G,Class,GLA,A
Friday, November 8, 2019
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Technical Service Bulletin # 12-04-21-001B Date: 130411
Subscribe to:
Post Comments (Atom)
No comments:
Post a Comment