2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 554
Conditions for Running the DTC
The RHSM must be powered.
Conditions for Setting the DTC
B1925 02 or B2170 02
The temperature sensor voltage drops below 0.80 V for more than 1 second.
B1925 05 or B2170 05
The temperature sensor voltage is greater than 5 V for more than 1 second.
Action Taken When the DTC Sets
The heated seat function for the affected seat will be disabled.
Conditions for Clearing the DTC
* The current DTC will clear 3 seconds after the reference voltage returns to normal operating range, and the ignition is cycled OFF then back
to ACC or RUN.
* A history DTC will clear after 50 ignition cycles or with a scan tool using the clear DTCs function.
Reference Information
Schematic Reference
Heated/Cooled Seat Schematics ()
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Heated Seats Description and Operation (KA1) ()Heated Seats Description and Operation (KA6) ()
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Verification
Verify the type of vehicle and the heated seat system for which the DTC set.
If the DTC set in the rear heated seat module, refer to Circuit/System Testing below.
If the DTC set in a vehicle equipped with memory, refer to DTC B1925 or B2170 (w/o HP2 with memory).
If the DTC set in a hybrid or a non-hybrid vehicle without memory, refer to DTC B1925 or B2170 (HP2 or dealer installed w/o memory).
Circuit/System Testing
B1925 02, B1925 05
1. Ignition OFF, disconnect the X2, X4 harness connectors at the RHSM.
2. Test for 850 Ohms - 300 kOhms between the signal circuit terminal 9 X4 and the low reference circuit terminal 6 X2.
瀚慖f less than the specified range, test for a short between the signal and low reference circuits. If the circuits test normal, replace the seat
cushion heater element/temperature sensor.
瀚慖f greater than the specified range, test the signal and low reference circuits for a short to voltage or an open/high resistance. If the circuits
test normal, replace the seat cushion heater element/temperature sensor.
3. Connect the X2, X4 harness connectors at the RHSM.
Mercedes Benz Diagnostic and Repair Information ,Wiring Diagrams. DTC. TSB. Types: TSB, DTC, Wiring Diagrams, OEM Procedures. Trusted by more than 400,000 technicians. OEM accurate fix for faster repairs. Repair Procedures and Labor Times. Factory Auto Repair info. Request A Demo Today. Factory-Correct Diagrams. Factory Part Numbers. Maintenance Schedules. Repair Procedures. Labor Times. Types: TSB, DTC.Mercedes,Mercedes,Benz,Mercedes-Benz UK,A,Class,B,Class,C,Class,E,Class,CLA,CLS,G,Class,GLA,A
Thursday, November 14, 2019
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 554
Subscribe to:
Post Comments (Atom)
No comments:
Post a Comment