Sunday, November 17, 2019

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 816

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 816

* Ignition voltage is greater than 9.5 volts.

* The brake pedal is not pressed.

* A DTC is not set for the other wheel speed sensor on the same axle.

Conditions for Setting the DTC

C0035 00-C0050 00

* A short to ground, or an open/high resistance is detected on the wheel speed sensor 12-volt reference circuit.

* A short to voltage, short to ground or an open/high resistance is detected on the signal circuit.

* Wheel speed sensor power supply is less than 7.6 volts.

* A missing wheel speed sensor signal

C0035 5A-C0050 5A

An erratic signal output of the wheel speed sensor is detected.

Actions Taken when the DTC Sets

* The EBCM disables the antilock brake system (ABS)/traction control system and vehicle stability enhancement system (VSES) for the

duration of the ignition cycle.

* The ABS indicator illuminates.

* The StabiliTrak indicator illuminates.

* The EBCM disables the voltage to the wheel speed sensor the fault is detected on.

Conditions for Clearing the DTC

* A current DTC clears when the diagnostic runs and passes.

* A history DTC clears after 100 consecutive ignition cycles, if no failures are reported by this diagnostic.

Diagnostic Aids

* Inspect the back of the wheel bearing on the encoder surface for metal debris that could cause an erratic reading with the sensor. Do not use a

magnet to clean the debris, or damage to the encoder ring may occur.

* If 2 or more wheel speed sensors are inoperative diagnose each wheel speed sensor individually.

* An ECE 13 response may be required, after repairs are made, and DTCs are cleared, operate the vehicle at speeds greater than 15 km/h (10

mph) to complete the self test, and the EBCM will turn off the ABS indicator.

If the customer comments that the ABS indicator is ON only during moist environmental conditions: rain, snow, vehicle wash, etc., inspect the

wheel speed sensor wiring for signs of water intrusion. If the DTC is not current, clear all DTCs and simulate the effects of water intrusion by using

the following procedure:

1. Spray the suspected area with a 5 percent saltwater solution. To create a 5 percent saltwater solution, add 2 teaspoons of salt to 8 fl oz of

water (10 g of salt to 200 ml of water).

2. Test drive the vehicle over various road surfaces: bumps, turns, above 40 km/h (25 mph) for at least 30 seconds.

3. Rinse the area thoroughly when completed.

Reference Information

Schematic Reference

Antilock Brake System Schematics (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Description and Operation

ABS Description and Operation (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Description and Operation/ABS

Description and Operation)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

No comments:

Post a Comment