2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 369
Conditions for Clearing
* The DTC will transition to history when the fault is no longer present.
* A history DTC will clear after 100 malfunction-free ignition cycles.
Diagnostic Aids
If the parking aid switch is continuously pressed for greater than 5 seconds the DTC will set.
Reference Information
Schematic Reference
Object Detection Schematics (See: Accessories and Optional Equipment/Collision Avoidance and Parking Assist Systems/Diagrams/Electrical
Diagrams)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Object Detection Description and Operation (UFT) (See: Accessories and Optional Equipment/Collision Avoidance and Parking Assist
Systems/Description and Operation/Object Detection Description and Operation (UFT))Object Detection Description and Operation (UVC) (See:
Accessories and Optional Equipment/Collision Avoidance and Parking Assist Systems/Description and Operation/Object Detection Description and
Operation (UVC))Object Detection Description and Operation (UD7) (See: Accessories and Optional Equipment/Collision Avoidance and
Parking Assist Systems/Description and Operation/Object Detection Description and Operation (UD7))
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Verification
Ignition ON, observe the scan tool Park Assist Switch parameter while cycling the parking assist disable switch. The parameter should change
between Active and Inactive.
Circuit/System Testing
1. Ignition OFF, disconnect the harness connector at the I/P multifunction switch.
2. Test for less than 1.0 Ohms between the appropriate ground circuit listed below and ground:
* RPO X88/Z88 ground circuit terminal 3
* RPO Z75 ground circuit terminal 5
瀚慖f greater than the specified range, test the ground circuit for an open/high resistance.
3. Ignition ON, verify that the scan tool Park Assist Switch parameter is Inactive.
瀚慖f not the specified value, test the signal circuit terminal 2 for a short to ground. If the circuit tests normal, replace the object alarm
module.
4. Ignition OFF, connect a 3A fused jumper wire between signal circuit terminal 2 and ground.
5. Ignition ON, verify that the scan tool Park Assist Switch parameter is Active.
瀚慖f not the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the
object alarm module.
6. If all circuits test normal, test or replace the I/P multifunction switch.
Mercedes Benz Diagnostic and Repair Information ,Wiring Diagrams. DTC. TSB. Types: TSB, DTC, Wiring Diagrams, OEM Procedures. Trusted by more than 400,000 technicians. OEM accurate fix for faster repairs. Repair Procedures and Labor Times. Factory Auto Repair info. Request A Demo Today. Factory-Correct Diagrams. Factory Part Numbers. Maintenance Schedules. Repair Procedures. Labor Times. Types: TSB, DTC.Mercedes,Mercedes,Benz,Mercedes-Benz UK,A,Class,B,Class,C,Class,E,Class,CLA,CLS,G,Class,GLA,A
Tuesday, November 12, 2019
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 369
Subscribe to:
Post Comments (Atom)
No comments:
Post a Comment