2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 574
Schematic Reference
Heated/Cooled Seat Schematics ()
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Heated Seats Description and Operation (KA1) ()Heated Seats Description and Operation (KA6) ()
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Verification
Verify the type of vehicle and the heated seat system for which the DTC set.
If the DTC set in the rear heated seat module, refer to Circuit/System Testing below.
If the DTC set in a vehicle equipped with memory, refer to DTC B2345 (w/o HP2 with memory).
If the DTC set in a hybrid vehicle without memory, refer to DTC B2345 (HP2 w/o memory).
If the DTC set in a non-hybrid vehicle without memory, refer to DTC B2345 (Dealer Installed).
Circuit/System Testing
B2345 00
1. Ignition OFF, disconnect the X1 harness connector at the RHSM.
2. Test for infinite resistance between the control circuit terminal 3 and ground.
瀚慖f not the specified value, test the control circuits listed below for a short to ground:
* Left rear seat heater element terminal 3
* Left rear seat heater element terminal 5
3. Test for infinite resistance between the control circuit terminal 6 and ground.
瀚慖f not the specified value, test the control circuits listed below for a short to ground:
* Right rear seat heater element terminal 6
* Right rear seat heater element terminal 2
4. Ignition ON, verify that a test lamp does not illuminate between the control circuit terminal 3 and ground.
瀚慖f the test lamp illuminates, test the control circuits listed below for a short to voltage:
* Left rear seat heater element terminal 3
* Left rear seat heater element terminal 5
5. Verify that a test lamp does not illuminate between the supply voltage circuit terminal 6 and ground.
瀚慖f the test lamp illuminates, test the control circuits listed below for a short to voltage:
* Right rear seat heater element terminal 6
* Right rear seat heater element terminal 2
6. If all circuits test normal, replace the RHSM.
B2345 13
1. Ignition OFF, disconnect the X2, X4 harness connectors at the RHSM.
2. Test for greater than 850 ohms between the signal and the low reference circuits listed below:
Mercedes Benz Diagnostic and Repair Information ,Wiring Diagrams. DTC. TSB. Types: TSB, DTC, Wiring Diagrams, OEM Procedures. Trusted by more than 400,000 technicians. OEM accurate fix for faster repairs. Repair Procedures and Labor Times. Factory Auto Repair info. Request A Demo Today. Factory-Correct Diagrams. Factory Part Numbers. Maintenance Schedules. Repair Procedures. Labor Times. Types: TSB, DTC.Mercedes,Mercedes,Benz,Mercedes-Benz UK,A,Class,B,Class,C,Class,E,Class,CLA,CLS,G,Class,GLA,A
Thursday, November 14, 2019
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 574
Subscribe to:
Post Comments (Atom)
No comments:
Post a Comment