Friday, November 15, 2019

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 671

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 671

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Description and Operation

Exterior Lighting Systems Description and Operation (See: Lighting and Horns/Description and Operation/Exterior Lighting Systems Description

and Operation)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Testing

1. Ignition OFF, disconnect the harness connector at the DRL resistor.

2. Connect a test lamp between the control circuit terminal C and B+.

3. Command the DRL ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded states.

瀚慖f the test lamp is always ON, test the control circuit for a short to ground. If the circuit tests normal, replace the BCM.

瀚慖f the test lamp is always OFF, test the control circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace

the BCM.

4. Ignition OFF, connect the harness connector at the DRL resistor.

5. Disconnect the harness connector at the inoperative headlamp assembly.

6. Connect a test lamp between the signal circuit terminal D and B+.

7. Command the DRL ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded states.

瀚慖f the test lamp is always ON, test the signal circuit for a short to ground. If the circuit tests normal, replace the DRL resistor.

瀚慖f the test lamp is always OFF, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace

the DRL resistor.

8. Connect a test lamp between the signal circuit terminal B and B+.

9. Command the DRL ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded states.

瀚慖f the test lamp is always ON, test the signal circuit for a short to ground. If the circuit tests normal, replace the DRL resistor.

瀚慖f the test lamp is always OFF, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace

the DRL resistor.

10. If all circuits test normal, replace the appropriate headlamp.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Headlamp Replacement (Cadillac Escalade) (See: Lighting and Horns/Headlamp/Service and Repair/Removal and Replacement/Headlamp

Replacement (Cadillac Escalade))Headlamp Replacement (GMC Yukon Two-mode Hybrid) (See: Lighting and Horns/Headlamp/Service

and Repair/Removal and Replacement/Headlamp Replacement (GMC Yukon Two-mode Hybrid))Headlamp Replacement (Yukon) (See:

Lighting and Horns/Headlamp/Service and Repair/Removal and Replacement/Headlamp Replacement (Yukon))Headlamp Replacement

(Chevrolet Tahoe Two-mode Hybrid) (See: Lighting and Horns/Headlamp/Service and Repair/Removal and Replacement/Headlamp

Replacement (Chevrolet Tahoe Two-mode Hybrid))Headlamp Replacement (Tahoe, Avalanche) (See: Lighting and

Horns/Headlamp/Service and Repair/Removal and Replacement/Headlamp Replacement (Tahoe, Avalanche))Headlamp Replacement

(Escalade PLATINUM) (See: Lighting and Horns/Headlamp/Service and Repair/Removal and Replacement/Headlamp Replacement

(Escalade Platinum))Headlamp Replacement (Non HID) (See: Lighting and Horns/Headlamp/Service and Repair/Removal and

Replacement/Headlamp Replacement (Non HID))

* Underhood Electrical Center or Junction Block Replacement (See: Maintenance/Fuses and Circuit Breakers/Fuse Block/Service and

Repair/Removal and Replacement/Underhood Electrical Center or Junction Block Replacement)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for BCM replacement, setup, and programming

With RPO Code X88, Z75, and Z88

No comments:

Post a Comment