2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 537

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 537

Reference Information

Schematic Reference

Driver Seat Schematics ()

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Description and Operation

Memory Seats Description and Operation ()

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

Ignition ON, observe the scan tool Driver Position Module driver seat and lumbar position sensor parameters. The readings should be between

0.22-2.75 volts and change while adjusting seat and lumbar positions.

Circuit/System Testing

B1825 01 or B1825 06

1. Ignition OFF, disconnect the harness connector at the seat recline position sensor.

2. Test for less than 2 ohms between the low reference circuit terminal 1 and ground.

瀚慖f greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the MSM.

3. Ignition ON, test for 4.8-5.2 volts between the 5-volt reference circuit terminal 3 and ground.

瀚慖f less than the specified range, test the 5-volt reference circuit for a short to ground or an open/high resistance. If the circuit tests normal,

replace the MSM.

瀚慖f greater than the specified range, test the 5-volt reference circuit for a short to voltage. If the circuit tests normal, replace the MSM.

4. Verify the scan tool Driver Seat Recline Sensor parameter is less than 1 volt.

瀚慖f greater than the specified range, test the signal circuit terminal 2 for a short to voltage. If the circuit tests normal, replace the MSM.

5. Install a 3A fused jumper wire between the signal circuit terminal 2 and the 5-volt reference circuit terminal 3. Verify the scan tool Driver

Seat Recline Sensor parameter is greater than 4.75 volts.

瀚慖f less than the specified range, test the signal circuit for short to ground or an open/high resistance. If the circuit tests normal, replace the

MSM.

6. If all circuits test normal, test or replace the seat recline position sensor.

B2355 01, B2355 06, B2365 01, B2365 06, B2375 01 or B2375 06

1. Ignition OFF, disconnect the X2 harness connector at the seat adjuster assembly.

2. Test for less than 2 ohms between the low reference circuit terminal 2 and ground.

瀚慖f greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the MSM.

3. Ignition ON, test for 4.8-5.2 volts between the 5-volt reference circuit terminal 6 and ground.

瀚慖f less than the specified range, test the 5-volt reference circuit for a short to ground or an open/high resistance. If the circuit tests normal,

replace the MSM.

瀚慖f greater than the specified range, test the 5-volt reference circuit for a short to voltage. If the circuit tests normal, replace the MSM.

4. Verify the appropriate scan tool driver seat sensor parameter is less than 1 volt.