2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 3120

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 3120

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Testing

1. Ignition OFF, disconnect the harness connector of the yaw rate sensor.

2. Ignition ON, verify that a test lamp illuminates between the module voltage circuit and ground.

瀚慖f the test lamp does not illuminate, test the circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the

EBCM.

3. Ignition OFF, test for less than 5 ohms between the module ground circuits and ground.

瀚慖f greater than the specified value, test the ground circuit for an open/high resistance. If the circuit tests normal, replace the EBCM.

4. If all circuits test normal, replace the yaw rate sensor.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* GMLAN Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Wiring Repairs/GMLAN Wiring Repairs)

* ABS Description and Operation (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Description and

Operation/ABS Description and Operation) for the ABS - Hybrid

* Vehicle Yaw Sensor with Vehicle Lateral Accelerometer Replacement (See: Brakes and Traction Control/Antilock Brakes / Traction

Control Systems/Yaw Rate Sensor/Service and Repair/Less than 3900 kg (8600 lb) GVW) for the ABS - Non-Hybrid Less than 3900 kg

(8600 lb) GVW

* Vehicle Yaw Sensor with Vehicle Lateral Accelerometer Replacement (See: Brakes and Traction Control/Antilock Brakes / Traction

Control Systems/Yaw Rate Sensor/Service and Repair/Less than 3900 kg (8600 lb) GVW) for the ABS - Non-Hybrid Greater than/Equal to

3900 kg (8600 lb) GVW

* Control Module References (See: Testing and Inspection/Programming and Relearning) for module replacement, setup, and programming

U2163

DTC U2105-U2199

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptor

DTC U2142 00

- Lost Communication With Yaw Rate Sensor (YRS)

Circuit/System Description

Modules connected to the CAN bus serial data circuits monitor for serial data communications during normal vehicle operation. Operating

information and commands are exchanged among the modules. The modules have prerecorded information about what messages are needed to be

exchanged on the serial data circuits. The messages are supervised and also, some periodic messages are used by the receiver module as an

availability indication of the transmitter module. Each message contains the identification number of the transmitter module.

The electronic brake control module (EBCM) activates the other modules connected to the CAN serial data circuits by applying voltage when the

ignition key is in ACC, ON or START. The EBCM, Yaw Rate and Lateral Acceleration Sensor are the only modules connected to the CAN bus